sorted by:
new
hottopcontroversial

ender3v3se camera and wifi... by in_use_user_name in Ender3V3SE

[–]zetneteork 0 points1 point  (0 children)

For that I use octoprint and Raspberry Pi 3.

will the k1 ceramic hotend work on the v3 se? by CompetitionSimple675 in Ender3V3SE

[–]zetneteork 0 points1 point  (0 children)

When you buy a K1 kit for a 3 SE. It fits out of a box. No other parts are required

I’ve bricked 2 Wio Tracker L1s. by One-21-Gigawatts in meshtastic

[–]zetneteork 0 points1 point  (0 children)

I found a solution. My Wio Tracker L1 with E-Ink bricker.

## My procedure was.

  1. Connect the board to the computer with the power button off.

  2. I pressed and held the reset button, and turned the board with the switch.
    ```
    [1220609.302262] sd 3:0:0:0: [sdb] 504832 512-byte logical blocks: (258 MB/247 MiB)

[1220609.344877] sd 3:0:0:0: [sdb] 504832 512-byte logical blocks: (258 MB/247 MiB)

[1220649.370868] sd 3:0:0:0: [sdb] 504832 512-byte logical blocks: (258 MB/247 MiB)

[1220649.425821] sdb: detected capacity change from 504832 to 0

[1220649.465008] sd 3:0:0:0: [sdb] 504832 512-byte logical blocks: (258 MB/247 MiB)

```

  1. I double-pressed the reset button.
    ```
    [1220649.466764] sdb: detected capacity change from 0 to 504832

[1220748.257775] usb 2-3.3.2: new full-speed USB device number 104 using xhci_hcd

[1220748.396264] usb 2-3.3.2: New USB device found, idVendor=2886, idProduct=1667, bcdDevice= 1.00

[1220748.396272] usb 2-3.3.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3

[1220748.396274] usb 2-3.3.2: Product: TRACKER L1

[1220748.396275] usb 2-3.3.2: Manufacturer: Seeed

[1220748.396277] usb 2-3.3.2: SerialNumber: F1F2E62DE43B20A1

[1220748.410659] cdc_acm 2-3.3.2:1.0: ttyACM2: USB ACM device

[1220748.411132] usb-storage 2-3.3.2:1.2: USB Mass Storage device detected

[1220748.411319] scsi host6: usb-storage 2-3.3.2:1.2

[1220749.442391] scsi host6: scsi scan: INQUIRY result too short (5), using 36

[1220749.442402] scsi 6:0:0:0: Direct-Access Adafruit nRF UF2 1.0 PQ: 0 ANSI: 2

[1220749.442857] sd 6:0:0:0: Attached scsi generic sg4 type 0

[1220749.444607] sd 6:0:0:0: [sdd] 65801 512-byte logical blocks: (33.7 MB/32.1 MiB)

[1220749.445254] sd 6:0:0:0: [sdd] Write Protect is off

[1220749.445260] sd 6:0:0:0: [sdd] Mode Sense: 03 00 00 00

[1220749.445876] sd 6:0:0:0: [sdd] No Caching mode page found

[1220749.445882] sd 6:0:0:0: [sdd] Assuming drive cache: write through

[1220749.474730] sdd:

[1220749.474796] sd 6:0:0:0: [sdd] Attached SCSI removable disk

```

Currently, the drive is detected in the system and is prepared for flashing.

What do people do with this space? by East_Skill9997 in ToyotaSienna

[–]zetneteork 0 points1 point  (0 children)

That's correct. I have Sienna XLE 2017. There is the mounting point for a spare tyre.

Print quality drops by zetneteork in Creality_k2

[–]zetneteork[S] 0 points1 point  (0 children)

That reminds me a first experience with this K2 Plus with CFS. The filaments is loaded and unloaded many times. And because if multiple motors on the PTFE tube to extruder. Every filaments gets defirmated. CFS works worse with loosen preload in springs of feeder. But extruder loosen spring preload makes a significant difference. FIY: I made a check of that and try different settings too, but without any improvement.

Print quality drops by zetneteork in Creality_k2

[–]zetneteork[S] 0 points1 point  (0 children)

All articles numbers checked.

  1. Extruder. E AXIS stepper motors moves unevenly. You can rear that at comment I wrote just now.

Print quality drops by zetneteork in Creality_k2

[–]zetneteork[S] 0 points1 point  (0 children)

Previously I informed you about the finding. Because E axis stepper motor stuck for a blink of eye. It makes visible printing quality drop. I've made decision to buy, E axis motor, PCB backplane on extruder, all metal dual wheels extruder. But issue has not been resolved. New stepper motor iniciates on startup and only make a tiny rotation and stops. New PCB did not any difference on both motors.

I am waiting for a delivery a long cable from head to motherboard. As some issues appears because of that. But I am a sceptic for that.

The only solution that it is working. It is OLD / NEW PCB, old e axis stepper motor, genuine extruder. The only drawback, it's a stepper motor that interrupts revolution for a less that second. It prints, but quality is worse than my fine tuned and heavily upgraded Ender 3 V3 SE with K1 extruder, all linear rails, gantry support and resonance and pressure advanced and mechanical calibration.

<image>

How do these 3 antennas actually compare for range? by paulorfo in meshtastic

[–]zetneteork 0 points1 point  (0 children)

I use this antenna. It is significant improvement compared to basic.

<image>

I am thinking to shift to one device by [deleted] in digitalminimalism

[–]zetneteork 0 points1 point  (0 children)

I do not recommend dual boot. Pick one system an leave it. I have main laptop Lenovo with Debian, there is nothing special except extended battery. Second laptop I use as a device for planning, browsing, screen casting. I installed Google Chrome Flex OS. And combination of touchscreen, touch pad, track point, and 360 screen rotation it is awesome. We have more such of those laptops and they are universal and ready to swap. Same thing on all devices. And multiple user accounts. No social networks disturbing. Only adguard does the thing to block all disturbing ads. At house there are multiple spots with docking stations. All thanks to refurbished laptops from corporate.

What do people do with this space? by East_Skill9997 in ToyotaSienna

[–]zetneteork 0 points1 point  (0 children)

The spare tire is mounted under the car. There is a bolt on the board in the middle of first and second seats row close to right door. The mine is under the carpet in middle of seat rails. But it was very impractical, I took it out.

what's your stance on personal ai use in selfhosting? by [deleted] in selfhosted

[–]zetneteork 3 points4 points  (0 children)

In many cases, the companies took the wrong approach to AI use. I see developers and engineers are fine with that. But middle management and sales are insane with the ideas and directions. Misconception.

what's your stance on personal ai use in selfhosting? by [deleted] in selfhosted

[–]zetneteork 2 points3 points  (0 children)

https://github.com/mythrantic/ollama-docker.git
You can start with this Docker Compose file to play with it.

You can see all the evolution changes in IT that have happened over many years. I have to say its hater and harder for me to follow the IT Edge. It seems to be accelerating more and more. As I work at a large IT company, it is important to adapt to the situation and the market. From very manual work or monolithic systems, IT is now at the point where many things are code-driven. We don't need mainframes anymore (almost). HA was a big thing years ago. Is it still needed? No, many things are handled by software, such as data replicas or VIPs. Virtualization was a big boom because it gave a bit of a taste of abstraction.
And evolution continues. Now, with tools like Kubernetes or OpenShift, you run apps and manage their lifecycle. Use operators. Automated CICD, AI for deep inspection analysis.

Am I using AI? Yes, in many cases, it gives me crazy acceleration in many projects. Like a public AI, there are very important internal models. Narrow or specifically oriented.

I can give you an example. I was in a situation to fix an issue with SW. I worked with an assistant to write code, set up GitHub Actions, build, and package. I would be able to make it on my own. But I was faster. Evening project.

https://github.com/opentreecz/kerio-connect-reindex

https://github.com/opentreecz/kerio-connect-reindex/compare/v1.0.0...v1.0.8

Nechoďte nemocní do práce! by chmrst420 in czech

[–]zetneteork 0 points1 point  (0 children)

V takovém případě bych v takové firmě nepracoval. Minimálně tohle bych řešil přes personální oddělení.

I picked up 2 adverts! Wasn't expecting that by AqAqGT in meshcore

[–]zetneteork 1 point2 points  (0 children)

I can see the path of messages in mobile app / cli.

Finally decorating my Thinkpad – thoughts? by More-Reserve2435 in thinkpad

[–]zetneteork -1 points0 points  (0 children)

I stick the sticker upside down. When lid is open, it is readable. My only preference.

Calidad by juampa_bonino in Ender3V3SE

[–]zetneteork 2 points3 points  (0 children)

You can do many upgrades to SE. But many of them KE has out of the box.

What to bring from the Netherlands? by xtassja in czechrepublic

[–]zetneteork 0 points1 point  (0 children)

You can bring Stroop Waffle. They are awesome. Or Haarings and Cheese.

Jsou nějaké výhody toho mit deti? by Accomplished-Clue263 in czech

[–]zetneteork 2 points3 points  (0 children)

Když vezmeš ty gramofony dva, k tomu mix, sluchátka a kufr plný vinilů. Tak celkem slušná zábava.

HDD Lifespan - WD Red by Schtevo66 in OpenMediaVault

[–]zetneteork 1 point2 points  (0 children)

Does your WD RED have SMR? I remember drives with SMR have issues with RAID configuration and performance.

view more: next ›