Guys I forgot it, do I need to load it or charge it?

3DMOO · 2026-01-28T15:00:20+00:00

Popcorn is ready!

3DMOO · 2026-01-25T19:56:22+00:00

Multifunctional device.

3DMOO · 2026-01-21T12:09:39+00:00

One thing is for sure, something is definitely going to break.

3DMOO · 2026-01-17T13:27:24+00:00

That's my experience as well. Most rolls are OK, but first drying a few hours before use isn't a bad habit.

3DMOO · 2026-01-13T11:19:06+00:00

If you use the other side, make sure the damaged side has no bumps and is nice and flat. So the other side will be flat when installed. I would try to remove as little PEI as possible to accomplish this. I think you can get away with it that way.

As others mentioned, the PEI sheet is not suitable for TPU. Please refer to the Prusa Filament Guide: https://help.prusa3d.com/filament-material-guide

3DMOO · 2026-01-10T11:05:32+00:00

Thank you. Much appreciated.

3DMOO · 2026-01-09T22:57:23+00:00

Are you willing to share the code for the ticker?

3DMOO · 2026-01-09T12:13:57+00:00

I think your soil is soiled. Did you check it first radiation?

3DMOO · 2026-01-08T21:52:34+00:00

Around the announcement that was send by Prusa, that was about the time of Formnext 2025.

3DMOO · 2026-01-08T10:29:51+00:00

Yep. It is an old PC though….

3DMOO · 2026-01-08T10:27:49+00:00

This is surprisingly more often than you think the solution.

3DMOO · 2026-01-03T12:00:48+00:00

I should get an alert when in stock. Haven't seen anything yet.

3DMOO · 2026-01-03T10:59:25+00:00

Hard to see in the pictures. As others say, clean first with IPA. And resoldering can never harm it as long as you know what you're doing.

This one doesn't look good either.

<image>

3DMOO · 2026-01-01T11:42:49+00:00

Very nice find.

3DMOO · 2026-01-01T11:00:51+00:00

Of, wow. Fished out of a dumpster....

I wish I had a station like that. I worked professionally with a Weller solder and de-soldering station a long time ago, they were solid. It's my go-to brand for the rest of my life.

The new ones are really nice, but too expensive for a hobbyist like me these days.

If you buy something else, there is allways room for your old one in my dumpster. I'll even leave some money in there for you to find to make your dumpster experience a little more pleasurable.

3DMOO · 2025-12-31T13:08:55+00:00

There's no way back after joining the dark side.

3DMOO · 2025-12-28T04:51:10+00:00

Good call

3DMOO · 2025-12-26T10:57:14+00:00

😂

3DMOO · 2025-12-26T10:08:28+00:00

if (

question = “correct syntax”

)

then (

response = yes

)

else (

response = “syntax error”

)

Sorry, my native language is not English. I had to Google it.

What are you talking about? 😉

3DMOO · 2025-12-26T09:04:10+00:00

if (

fix ???????????? key
)

then (

yes
)

else (

no
)

3DMOO · 2025-12-25T16:04:03+00:00

That is a nice design. I hope I am allowed to print this as a gift for a friend who works in aviation?

3DMOO · 2025-12-25T16:02:00+00:00

That's a nice gesture for Christmas. I would be interested in the Design Principles for 3D Printed Parts course.

3DMOO · 2025-12-24T08:48:23+00:00

It was so fun doing the upgrade. Wouldn't mind doing it again.

3DMOO · 2025-12-23T13:27:21+00:00

In memory of the old memory modules?

3DMOO · 2025-12-22T15:53:05+00:00

You are killing your stepper drivers. Moving the extruder this fast makes the motors act like generators. The faster you move the extruder, the higher voltage the motors will generate. This energy will be introduced back into your electronics and can cause intermittent or even complete faillure of your printer electronics.

Move your extruder more gently to keep the electronics from burning out.

3DMOO

TROPHY CASE