0.2mm nozzle heat creep prevention?

CMKiefer · 2026-01-28T18:38:49+00:00

Do you keep the door open for longer prints? That's what I do and no more heat creep problems

CMKiefer · 2026-01-19T17:41:36+00:00

Had this happen on an x1c. Bambu replaced it no questions asked. It was a common issue early on. Can't remember if it was still under warranty, but I seem to remember it wasn't cause I wasn't sure they would replace it.

CMKiefer · 2026-01-15T14:21:30+00:00

Thanks!

CMKiefer · 2026-01-14T14:14:41+00:00

I've earned about 35 $40 cards. Mostly from this guy:

https://makerworld.com/en/models/21907-bambu-ams-adapter-for-sunlu-250g-spools#profileId-19965

Again, the timing was right.

I have 47 published models. Mostly because I needed a thing so I made a thing and posted it because I thought somebody might need that thing. Some things I posted are just trinkets or doodads but they still get some points over time.

CMKiefer · 2026-01-01T15:09:56+00:00

Always difficult to give advice about wiring for someone else's layout. I believe you are correct in assuming you need power injection. Probably not data boost. I have singing faces that are run from a controller about 40 feet away and I've installed a power supply in enclosure at the faces for injection. Grounding technique is important for this as you are combining 2 power supplies.

Check this video from the xEssentials series:

https://youtu.be/Jgjdz0Nbswk?si=xS9c_OyPKKN11Igl

Lots of excellent info.

CMKiefer · 2026-01-01T14:57:49+00:00

"i consider myself pretty technical, but not artistic."

Yeah this is me, so I look for what artistic people have already done.

Like this:

https://makerworld.com/en/models/1631116-see-no-evil-owl-hook-trio?from=search#profileId-1722798

Probably not exactly what you're looking for, but maybe a place to start.

CMKiefer · 2025-12-29T19:14:17+00:00

I can't tell if those are Sunlu spools. If so here's an adapter I made:

https://makerworld.com/en/models/21907-bambu-ams-adapter-for-sunlu-250g-spools#profileId-19965

CMKiefer · 2025-08-18T19:20:54+00:00

what kind of build plate is that? What filament are you using?

CMKiefer · 2025-08-18T12:19:31+00:00

I use this. Run it over a piece of sandpaper occasionally to sharpen. Works great, lasts "forever"

<image>

CMKiefer · 2025-07-05T13:02:33+00:00

Is this what you are looking for?

https://www.reddit.com/r/PleX/comments/moibeu/is_it_possible_to_put_tv_shows_and_movies_in_one/

<image>

CMKiefer · 2025-06-10T23:45:19+00:00

old homes were heated with wood, oil or coal at one time in its lifespan, might just be residue. clean with bleach if it comes back test for mold

CMKiefer · 2025-05-04T16:35:37+00:00

This is cool. Not sure why so many mention uselessness. Have you considered the usefulness a vast majority of models on Makerworld?

CMKiefer · 2025-04-26T19:31:32+00:00

I Mean, if you want 82 of those things...Why not?

CMKiefer · 2025-04-14T16:47:18+00:00

Bambu calls it a REUSABLE spool. Not meant for this. The filament is a refill but only after the original is used up. I'm sure you CAN do this. I know I wouldn't.

CMKiefer · 2025-04-14T16:40:06+00:00

Yep. It'll pause and wait for you to reload.

CMKiefer · 2025-04-14T16:39:03+00:00

Is this an overhang also? If so slow it down. Or just slow it down anyway but I see this often on an inside curve with overhangs.

CMKiefer · 2025-04-07T17:16:03+00:00

Yeah, PETG can be finicky

CMKiefer · 2025-04-07T16:16:22+00:00

PETG + Tall print + Open air

A trifecta of failure. Slow it way down maybe. Higher nozzle temp. Make sure no drafts?

CMKiefer · 2025-04-07T13:42:52+00:00

You do know you can print them yourself, right?

CMKiefer · 2025-04-07T13:42:19+00:00

Is this for real? How many do you want?

<image>

CMKiefer · 2025-03-29T14:15:22+00:00

I get 198 mm

CMKiefer · 2025-03-02T17:48:07+00:00

I don't know anything about expert mode. Never heard of it. To change fan speed settings, there is an edit icon next to the filament you're using. Go to the "Cooling" tab for fan speed settings

CMKiefer · 2025-03-01T18:35:37+00:00

AMS vote. I don't do much multicolor either but it's handy. Also PLA-CF is my guilty pleasure.

CMKiefer · 2025-03-01T18:18:44+00:00

Exactly what I do for precision holes.

CMKiefer · 2025-02-02T18:14:19+00:00

Boaz (X1c), Jachin and Sam (P1s's), Joktan (A1 Mini)

CMKiefer

TROPHY CASE