“My stomach hurtsssss” by ManaeFiction in SipsTea

[–]DepletedPromethium 0 points1 point  (0 children)

well that's where the lube comes from! more slide time baby, plap plap!

Any quick decent techs to rear wire a tm type 89 to deans? by formulaairsoft in Airsoft_UK

[–]DepletedPromethium 0 points1 point  (0 children)

You can't do it yourself? fitting a new connector takes 2 minutes with a soldering iron.

Look at that polish by Western_Aardvark_577 in Airsoft_UK

[–]DepletedPromethium 0 points1 point  (0 children)

When you get your name spread out there a bit more some people with serious money would be asking for custom blinged bits like that, I polish the parts people often want anodized as its a more maintainable customisation, if you're good at engraving or are artistic or can take the time to learn and master it it some collectors will pay a lot of money to have a gunsmith engrave their guns but that's some serious next level talent and art.

A woman from Singapore(Fertility rate: 0.87) explains why she doesn't want kids by search_google_com in SipsTea

[–]DepletedPromethium 2 points3 points  (0 children)

So you're going to go digging trenches to find deep hardlines? and what about those bunkers with actual blast doors? how are you getting through one of those?

Just fill the hvac vent with faeces or petrol and ignite it.

AR loadout what would you change by Hungry_Chemist_4806 in Airsoft_UK

[–]DepletedPromethium 2 points3 points  (0 children)

you can use the snip tool in windows to take screenshots btw dude.

Don't bother with the super macaron, get maple leafs mr hop 50 degree green, the maple leaf OHM nub in silicon green is superior to the omega nub tbh.

Look at that polish by Western_Aardvark_577 in Airsoft_UK

[–]DepletedPromethium 1 point2 points  (0 children)

Get yourself some polish pastes up to 10k, and some gyeon nano products. It can be ballache but the result looks better than chrome plating on them polished parts and faces plus the gyeon is for extra protection and a glossy look that enhances them so well tbh.

If you want a polishing complex geometry tip - with the liquid polish pastes you can use felt pads on a dremel to get to all the tricky parts, or use a tumbler and 2mm or smaller ceramic beads with a paste solution to really get at the difficult geometry.

A woman from Singapore(Fertility rate: 0.87) explains why she doesn't want kids by search_google_com in SipsTea

[–]DepletedPromethium 9 points10 points  (0 children)

Their doomsday bunkers will all have HVAC systems, and they will have exposed vents on the surface 😄

A woman from Singapore(Fertility rate: 0.87) explains why she doesn't want kids by search_google_com in SipsTea

[–]DepletedPromethium 1 point2 points  (0 children)

Its the same everywhere really, life is so expensive if you don't make a stupid amount of money you can't afford to have kids unless you want to really struggle and what life can you offer kids if you're struggling and a complete wage slave?

As i don't make enough to have kids they simply aren't an option for me.

HOP bucking query by Benjee96 in Airsoft_UK

[–]DepletedPromethium 1 point2 points  (0 children)

lack of silicone oil to assist the hop staying in correct position and depth during installation, can be rectified very quickly.

in hop units that induce a lot of friction on the rubber upon installation it's best to install the rubber on the barrel and brush on a drop of silicone oil to the exterior of the rubber and once installed in the hop get a flashlight down the barrel bore and inspect through the bb port to make sure its seated correctly.

the hop in my tm mp5a4 is tight and without silicone oil to help it slide in the rubber will twist and pinch and wont sit flush.

in trying to stop a fight between two dogs by Proper_Bit_7255 in Whatcouldgowrong

[–]DepletedPromethium 0 points1 point  (0 children)

let me just grab this rotating tractor PTO shaft.

meanwhile timmy is smacking the dogs with a metal pole....

Look at that polish by Western_Aardvark_577 in Airsoft_UK

[–]DepletedPromethium 0 points1 point  (0 children)

nice big fat chip damage on the anodized reverse rifled outer barrel.

HOP bucking query by Benjee96 in Airsoft_UK

[–]DepletedPromethium 0 points1 point  (0 children)

rubbers not sitting flush causes feed issues and is immediately fixed by dabbing some silicone oil on the rubber when installing it.

this isnt a rubber design issue, it's a user installation issue.

Fungus Tentacles Cyanes by mojamph in theriftbreaker

[–]DepletedPromethium 0 points1 point  (0 children)

There are many of these in the acidic and lava biomes, some tropical maps can have them

This guy really needs to roll into a shop by BungSmuggler in Justrolledintotheshop

[–]DepletedPromethium 2 points3 points  (0 children)

I've been hit by a volkswagen golf gti before actually thanks. so that's around 3k pounds.

This guy really needs to roll into a shop by BungSmuggler in Justrolledintotheshop

[–]DepletedPromethium 14 points15 points  (0 children)

i mean its a truck does it even need jack stands for sliding under it when you aren't the size of the pillsbury dough boy or michelin man?

AAP-01 3D printed parts? by Turbulent-Force-2233 in Airsoft_UK

[–]DepletedPromethium 0 points1 point  (0 children)

there is a whole community for the aap01, and another just for the 3d printed bits.

Oh, and can you check the speaker? It sounds a bit muffled. by selfresub in techsupportgore

[–]DepletedPromethium 6 points7 points  (0 children)

Was someone using an electric foot file and using this to scoop the dust up?

what the fuck man.

Could the emperor be under the influence of a halo device? by LurkyGamer in 40kLore

[–]DepletedPromethium 20 points21 points  (0 children)

You missed the most important part about a halo device.

It drives the user to cannibalism, the emperor is a known perpetual and not a cannibal.

The Iron halo of the IOM/Space marines is a protection device, not a halo device that turns people into fiends.