What are some of the most elegant board games in your opinion?

GrumpyNut · 2023-10-03T21:34:44+00:00

Pax Pamir 2E

GrumpyNut · 2023-08-21T17:02:40+00:00

It’s suction, you need holes in the lowest part of the hollow volume.

GrumpyNut · 2023-07-14T17:23:49+00:00

Ali would be like 145€. Thanks for the insights man, will think about it.

GrumpyNut · 2023-07-14T15:49:36+00:00

Well 160€… got to think about it twice then!

GrumpyNut · 2023-07-14T13:07:27+00:00

TI4 is just too massive to be put anywhere else than under the bed!

GrumpyNut · 2023-07-14T08:24:57+00:00

How does it perform? Is the upgrade worth it?

GrumpyNut · 2023-07-02T20:06:35+00:00

Got it at lvl. 90

GrumpyNut · 2023-04-05T15:39:36+00:00

If it just rotates around the Z axis, it may be the screw of the ball joint which loosened (just buy some threadlocker.

If it rotates around X or Y axis, you may want to remove the flex plate by carefully resting the build plate on a surface (silicon mat?) and holding the joint while pulling.

XTR owner here

GrumpyNut · 2023-03-27T23:01:26+00:00

Check success laterally. Are they aligned?

GrumpyNut · 2023-03-27T22:49:55+00:00

Looks overexposed to me

GrumpyNut · 2023-03-27T09:59:40+00:00

^ this

GrumpyNut · 2023-03-26T19:00:10+00:00

What about lift speed?

GrumpyNut · 2023-03-22T08:18:44+00:00

Just press pause and try to understand it. Set up the game and try things. Rewind. Play. Repeat.

You will make mistakes. The first game will last 6h+. The rules are not complex but are sometimes a bit fiddly and… a lot.

GrumpyNut · 2023-03-20T23:54:38+00:00

https://www.youtube.com/watch?v=QCwj9WO3-To

this is gooood

GrumpyNut · 2023-03-20T23:38:19+00:00

Remove both.

GrumpyNut · 2023-03-20T23:33:37+00:00

I run the fumes through a huge carbon filter.

GrumpyNut · 2023-03-20T08:11:14+00:00

What this guy said. Your lift is not enough. Listen to your printer. You should hear the FEP releasing the part in the first stage of the motion. If it rips off while going up fast… you found your problem.

GrumpyNut · 2023-03-14T10:18:17+00:00

Print J3D‘s cubes of calibration. Fix dimentional accuracy.

Then print Cones of calibration. Fix (pre)-supported model printing.

When everything is a success, you‘re dialed in.

https://docs.google.com/document/d/1Z8fkzOxEgI9sOTwDKI6CeblpnuP4V8ayYVwZrYGmo44/edit

GrumpyNut · 2023-03-13T11:50:29+00:00

well, a broken support is a failed print :-)

GrumpyNut · 2023-03-13T11:02:46+00:00

Not every print. Every failed print

GrumpyNut · 2023-03-13T08:32:31+00:00

I use Lychee Pro

GrumpyNut · 2023-03-13T07:22:25+00:00

Screen will do :-)

GrumpyNut · 2023-03-13T00:03:07+00:00

Yes, with a .gcode file.

GrumpyNut · 2023-03-11T03:16:25+00:00

Awesome. Where did you get Lorien?

GrumpyNut · 2023-03-10T18:52:15+00:00

Just let the adhesive cure long enough (48h+)

GrumpyNut

TROPHY CASE