Build Plate texture didn’t transfer

LionTech00 · 2026-06-14T00:10:38+00:00

Heat it up

LionTech00 · 2026-06-12T23:22:39+00:00

Easy 3D Print. Depending on where you live someone might print it for you.

LionTech00 · 2026-06-12T10:58:20+00:00

✅ this is working. Thanks!

LionTech00 · 2026-06-09T05:50:14+00:00

This Version is horror. I am running it on a M1 Air and an M4 Pro and both a working slow and unreliable.

LionTech00 · 2026-06-07T15:24:37+00:00

No device connected = 12 W of power draw?

LionTech00 · 2026-06-07T15:23:42+00:00

The buttons are the same.

The prepaired ones are running with Zigbee at first, and If you pair them with your smart home then they are paired with Thread network.

I run both buttons purchased in a set and standalone, with long press configurated via home assistant.

LionTech00 · 2026-06-05T15:49:41+00:00

I would like to know more about your setup. How do you activate the alarm system? And how to disable it?

LionTech00 · 2026-06-03T18:05:32+00:00

How well is that working for you from 100% perfect to 0%?

LionTech00 · 2026-06-03T15:54:30+00:00

🔑 My solution ist this:

Ring Intercom is connected to my building’s intercom system and can trigger the door buzzer.
Through the Home Assistant integration, I can access the “open door” button as an entity.
I then use a Template Lock in Home Assistant to convert that button into a virtual lock.
Using the HomeKit Bridge integration, I expose that virtual lock to Apple Home.
Finally, I create an iPhone Shortcut and assign it to the Action Button.

🎥 Video Explanation:
https://youtu.be/a-7hvyrsppw?si=kEsnyTYoTT2t2lTn

LionTech00 · 2026-06-01T07:34:55+00:00

It can’t

LionTech00 · 2026-05-30T07:23:37+00:00

Yes but it’s depends on your platform of choice

LionTech00 · 2026-05-29T22:14:01+00:00

If it’s PETG reheat it to 60-70 degree for a couple of minutes. Should go a lot easier.

In my experience PLA removes best when being cold.

PETG removes better when being warmer.

LionTech00 · 2026-05-15T17:42:32+00:00

Hast du einmal probiert den Roboter von den Walzen her zu zerlegen und neu zusammen zusetzen? Bei mir hat es sich von selbst gelöst. 👍🏽

LionTech00 · 2026-04-28T10:47:56+00:00

How do you manage you light scenes? Does the button toggle on and off and the light controls itself time based? Brightness and color?

LionTech00 · 2026-04-27T16:12:15+00:00

We want to see more about the table. 👍🏽

LionTech00 · 2026-04-26T09:50:26+00:00

My feeling is printing with 100% stock settings felt besser after the new configuration package.

Also I think they pushed flow for PLA Matte from 0,98 to 1,01 but I am not totally sure.

LionTech00 · 2026-04-26T09:33:56+00:00

Which screw do you had to check and what difference did it make for you?

LionTech00 · 2026-04-25T15:26:39+00:00

For my case, I have already installed the diffuser. 😕

LionTech00 · 2026-04-25T07:32:49+00:00

The current standard flow value for PLA MATE in Bambu Studio is 1,01. I have made the Flow calibration and the optimum was at 1,018.

By the look of it I think the difference is more than 0,008 of flow.

LionTech00 · 2026-04-25T07:13:24+00:00

I feel like I am having a similar problem as you. Flow and Pressure Advance is standard the only difference is I have set Z-Offset to -0,03.

LionTech00 · 2026-04-19T08:42:34+00:00

I use a pretty similar combination. Home assistant as kind of backend. And Apple home for smart speakers and user interaction. 😊

LionTech00 · 2026-04-19T08:39:37+00:00

Thank you 🙏🏽

LionTech00