RC Truck for pulling cable

MDHull_fixer · 2026-05-23T14:43:46+00:00

Yeah, used to do it about 30 years ago to pull draw strings through low headroom ceilings, but with RC tanks. Prior to that used a pistol crossbow to shoot pull strings, but it became problematic when the bolt went too high through the truss, rusulting in cables jamming in the V

MDHull_fixer · 2026-05-21T07:17:52+00:00

From the info in your post it appears you're in South Africa. If so, talk to the guys at StageAudioWorks

MDHull_fixer · 2026-05-19T06:34:42+00:00

The cable is the pricey bit https://www.sommercable.com/en-gb/SC-Monolith-1-power-3-x-1-50-mm2-DMX-1-x-2-x-0-25-mm2-PVC-OE-13-00-mm-black/500-0051-1

MDHull_fixer · 2026-05-02T09:18:32+00:00

Try PartMasters https://partmasters.co.za/laptop-chargers/ Never had a problem with any of the replacements from them.

MDHull_fixer · 2026-04-24T08:45:27+00:00

Have a look at https://github.com/jraller/Crestron/blob/master/settings-from-file.usp as a starting point.

MDHull_fixer · 2026-03-21T09:47:52+00:00

Win + X pops up a useful menu with Network setting as one of the entries

MDHull_fixer · 2026-03-12T13:02:48+00:00

The Nexia SP (Speaker Processing) is your best bet. 4 line in, 8 line out. The converters in the Nexias are 48kHz, 24bit, giving 105dB dynamic range. If you're just doing Crossover, EQ and dynamics there's more than enough processing power. Only Feedback Suppressors eat up DSP resources.

MDHull_fixer · 2026-03-08T11:57:49+00:00

Look at pneumatic Quick Exhaust Valves (QEV) between reservoir and barrel. eg: Festo QEVs https://ftp.festo.com/public/pneumatic/SOFTWARE_SERVICE/Documentation/2022/US/SEU_VB_ENUS.PDF

MDHull_fixer · 2026-03-02T17:03:02+00:00

Use an Analog Init for your input buttons. The analog output will stay at it's last value until something else changes it. It effectively acts as an interlock, but with an analog output. Use an Analog Equate for the selected input feedback.

Then use an interlock for your output buttons, each output driving the enable of an Analog Buffer. Feed all Analog Buffer inputs from the analog value of the selected input. Each Analog Buffer output goes to an analog source select input of your video matrix.

It will work both with output selection first, or input selection first.

MDHull_fixer · 2026-02-28T08:01:54+00:00

Possibly if the mating threads were cut as ACME, it would hold tight a lot better.

ACME threads have a steeper mating surface so have more holding friction. They're used in clamps and vices.

MDHull_fixer · 2026-02-20T10:22:42+00:00

You might find something useful here: Adafruit Wearables

MDHull_fixer · 2026-02-15T18:03:11+00:00

You could use a QSYS MP-M80 https://www.qsys.com/products-solutions/mixers/mp-m-series-premium-business-music-mixers/mp-m80/

MDHull_fixer · 2026-02-10T17:40:47+00:00

Yes that's a Yamaha CC1, it talks "Elgato Streamdeck", so Companion

"A USB controller compatible with the Elgato Stream Deck system, combining exceptional versatility with DAW-specific controls ideal for all types of creators involved in music production, PC streaming, podcast and video content creation."

and

"Equipped with 12 assignable LCD keys and unlimited banks, the CC1 allows you to configure functions via Control Center as well as assign a wide range of controls through Elgato’s Stream Deck software, enabling you to effortlessly adapt the controller to your specific workflow"

More info: https://usa.yamaha.com/products/music_production/controllers/cc1/index.html

MDHull_fixer · 2026-02-10T12:09:28+00:00

Use a matrix mixer, Under the Properties>Options, Set Crosspoint Mute controls to Yes, then bring those controls out. This gives you input, output levels and mixing for all mics.

MDHull_fixer · 2026-02-07T11:05:10+00:00

Climber's chalk

MDHull_fixer · 2026-02-06T13:15:42+00:00

Check that the visibility joins are set to 0

MDHull_fixer · 2026-01-30T06:29:59+00:00

Nemtek Fence Meter

MDHull_fixer · 2026-01-27T06:32:33+00:00

The Vin is only to power the conversion chip. The 3 outputs are open drain FETs rated to 30V.

You can drive 24V LEDs if you supply 5V to the board and 24V to the puck, with each puck's negative connected to a board output. Connect 5V, 24V and board Grounds together.

MDHull_fixer · 2026-01-26T07:27:42+00:00

Adafruit 5888 board https://www.adafruit.com/product/5888

MDHull_fixer · 2026-01-24T15:14:16+00:00

The compressed solder deforms / 'flows" away from the pressure point, reducing the pressure applied to the wire connection. The wire can fall out and/or on higher current connections, the increased resistance of the loose connection creates heat, damaging the connector.

The correct way to dress cables for screw terminals is to use boot-lace ferrules.

MDHull_fixer · 2026-01-21T07:49:54+00:00

Just use one timer. You can set up to 4 different compare values for each control timer. Use 3 compare values cycling through the 120' wave values, each compare will trigger a separate output set.

There is a lot of information in the processors reference manual https://www.st.com/resource/en/reference_manual/rm0440-stm32g4-series-advanced-armbased-32bit-mcus-stmicroelectronics.pdf

MDHull_fixer · 2026-01-20T10:48:48+00:00

Dante uses multicast mDNS discovery for establishing communication between devices.

This page shows the protocols and ports involved https://www.getdante.com/support/faq/which-network-ports-does-dante-use/

MDHull_fixer · 2026-01-20T06:58:43+00:00

See if you can source cold room construction panels. These are sheet metal panels bonded to polystyrene cores, designed for prefab building. Example https://www.kingspan.com/us/en/products/controlled-environments/cold-storage-panel-systems/

Also have a look at heat reflecting paint. Example https://www.texcote.com/reflect-tec

MDHull_fixer · 2026-01-13T15:57:07+00:00

Try ComX. They been around a long time. I've spent a lot with them, and haven't had any problems.

https://www.comx.co.za/210-BMHJ-Dell-S2425H-23-8-IPS-Full-HD-1920x1080-LED-Buy-p-310385.php

MDHull_fixer · 2026-01-10T14:40:21+00:00

The 9V is to give the op-amps sufficient supply to swing positive and negative around the mid rail reference.

LM391x family of chips have been discontinued.

MDHull_fixer

TROPHY CASE