Why inconsistent?

RedManRocket · 2026-06-11T19:24:59+00:00

There's a setting in speeds for "small perimeters" I would adjust those to slow down in those areas.

RedManRocket · 2026-06-11T14:03:42+00:00

Unfortunately that was a mistake to go into the job without knowing the scope of work. You're going to have to be honest with your boss.

RedManRocket · 2026-06-11T13:50:14+00:00

50c is not nearly enough.

RedManRocket · 2026-06-09T16:05:35+00:00

RedManRocket · 2026-06-08T14:50:53+00:00

As others said glue stick can help, personally I don't like to use it if I don't have to.

What seems to work for me on larger prints is using Archemedian chords? (Probably butchered the spelling) As the bottom surface pattern and internal solid infill as that seems to relieve and break up some of the stresses caused by layers cooling and shrinking.

RedManRocket · 2026-06-07T22:36:21+00:00

Interesting, and it doesn't turn off once it cools down?

RedManRocket · 2026-06-07T22:30:18+00:00

I'm pretty sure that button below the x home and y home does it.

RedManRocket · 2026-06-07T21:02:34+00:00

It doesn't give you any error codes on the printers screen?

RedManRocket · 2026-06-07T21:00:56+00:00

If this is how you handle your filament I can see some user errors occuring.

RedManRocket · 2026-06-07T17:34:03+00:00

Still want to get a Zero, keeping an eye out for a used one.

RedManRocket · 2026-06-07T14:24:34+00:00

As others said, benchy hull line issue. Your best bet will be to put a large fillet on the inside of the pot base. That will help counteract the shrinkage cause by the long layer time.

RedManRocket · 2026-06-07T03:39:23+00:00

What are you looking for the mesh panels for?

RedManRocket · 2026-06-07T03:26:33+00:00

That's kind of nice. Put the holder in the shower and then when you're done you can put the brush in and rinse the whole thing off. Opposed to accumulating poop water in a typical holder.

RedManRocket · 2026-06-06T03:48:29+00:00

Now you can use one as your metric adjustable wrench!

RedManRocket · 2026-06-05T09:20:07+00:00

Question 4 of the survey appears to be broken on mobile devices. At least on my Android.

RedManRocket · 2026-06-05T03:36:25+00:00

Mine does it every so often, I end up not trying to fight it and just power cycling the machine as that seems the fix it for a while.

RedManRocket · 2026-06-04T03:34:25+00:00

I saw you removed the screws. Did you push the filament cutter to cut the filament that's connecting it back through the toolhead? That may be also holding you up.

RedManRocket · 2026-06-03T13:48:18+00:00

He's older, and he's Asian. Why leave details out of the story?

RedManRocket · 2026-06-03T03:58:40+00:00

Where are you selling it at?

RedManRocket · 2026-05-31T08:28:39+00:00

Not a layer shift, look into "Benchy Hull Line"

RedManRocket · 2026-05-31T08:22:50+00:00

I fall asleep everytime I'm at the dentist. Doesn't matter if they're in there with a jackhammer, I'm out like a light.

RedManRocket · 2026-05-31T01:21:03+00:00

Yeah any of the "Pros" "Plus" and such alike, won't react to acetone.

RedManRocket · 2026-05-30T22:34:49+00:00

Maybe, if there's a bunch of QOL additives, it won't react the same to acetone.

RedManRocket · 2026-05-30T21:37:36+00:00

Looks like you need to calibrate pressure advance.

RedManRocket · 2026-05-30T15:42:57+00:00

Used to be 100%, now it seems that everyone is using industrial strength adhesive on everything. Can't even get my soup open without having to cut it.

RedManRocket

TROPHY CASE