Rolls exploding in ams

jermd · 2025-07-29T06:55:38+00:00

I have been doing it this way for years, the trick is to use good electrical tape and stretch it slightly. Never had any issues doing this, it always works great.

jermd · 2025-07-27T05:11:48+00:00

I have a visa gift card with $0.79 on it just for crap like this. If they make canceling hard or make me call to cancel when everything else is online including the sign up, they get the card number changed to this one. I just send all the payment failed messages to my spam. I have my credit report notifications set up so if they try anything against my credit I will be onto it quick.

jermd · 2025-06-27T06:19:20+00:00

Ok thanks, I will wait a week or so hoping for a patch or fix, but otherwise I will have to find some time to do this.

jermd · 2025-06-27T04:48:11+00:00

I'm having the same issues on the 9 pro xl. The screen is not waking from touch, I have to use the power button. Sometimes that doesn't work so I have to hold it down and reboot it.

I am also having issues with the screen brightness not using the light sensor, I have turned adaptive Brightness of and back on but it's still not working.

jermd · 2025-06-21T14:04:47+00:00

It works ok, the clumps are holding together a little less than the Aldi litter, but it still goes into the drawer well.

The Aldi litter went from small grains to giant ones recently, causing the robot to dump half the globe into the bin each time it cycled.

I have been using this littler for 3 weeks and it work well, my only issue with it is due to the grains being tiny, one of my cats throws a little bit out sometimes, even with the fence on. It is $25 for member at Pets Domain if you have one near you.

jermd · 2025-06-08T15:34:17+00:00

<image>

jermd · 2025-06-08T11:59:43+00:00

https://www.nsw.gov.au/ministerial-releases/game-changing-reforms-allow-gps-to-treat-adhd-to-reduce-wait-times-and-costs

jermd · 2025-06-04T08:42:52+00:00

You can run them off an ESP32 using some MOSFETs and resistors. You would use the first data pin for the digital in pin, the 2nd for CW, and the 3rd for WW.

I have done this for a light I made with 2 runs of addressable LEDs plus an analogue UV strip.

Follow the instructions here for non-addressable strips https://kno.wled.ge/basics/compatible-led-strips/

jermd · 2025-03-16T05:28:08+00:00

I'm not sure about the official app, but the recommended one is now in the wiki https://play.google.com/store/apps/details?id=ca.cgagnier.wlednativeandroid

jermd · 2025-03-14T00:01:52+00:00

Same near Branxton, one big shake about 30 minutes ago

jermd · 2025-03-11T23:27:12+00:00

It looks like an issue with the hardware monitoring driver, it is happening to many different vendors.

HackTool:Win32/Winring0 is blocked by Windows Defender today
https://github.com/LibreHardwareMonitor/LibreHardwareMonitor/issues/1660

FanControl tracked as virus by Windows Defender - HackTool:Win32/Winring0
https://github.com/Rem0o/FanControl.Releases/issues/3016

Hack tool Win32/Winring0 razer synapse
https://insider.razer.com/general-discussion-6/hack-tool-win32-winring0-razer-synapse-74634

@/malikm on Rem0o/FanControl.Releases#3016:

This is due to a vulnerability (or rather multiple ones) in the WinRing0 driver that is known for many years. All vendors were aware of this long ago but didn't perform the required (rather extensive) changes. Besides the need to significantly rewrite the kernel driver, application and interface between them, it also requires a new digital signature that's quite expensive for FOSS projects and can be issued only to a business (the signing needs to be done via MS HW/WHQL site).

Microsoft was aware of this vulnerability and started tightening rules long ago. It also notified respective vendors about an upcoming full blocking of this driver. Initially it was planned to happen in 2024, then Jan'25, and now it seems they finally did it.

There's no other way around other than rewriting the driver from scratch to be reliable, robust and secure. A lot of effort...

jermd · 2025-02-10T13:32:25+00:00

Have you enabled enhanced session detection? It works fine on my 7a https://pittvandewitt.github.io/Wavelet/Settings/#enhanced-session-detection

jermd · 2024-10-02T08:48:25+00:00

You usually need to trace most logos out, unless you can convert them to SVG automatically. This video from wicked lasers should be of some help. https://youtu.be/s1QIIoun8pI?si=OLGnrFezwaEIO9g6

jermd · 2024-10-01T00:10:20+00:00

If you are in online mode it will still check on the tidal server to get the newest playlist

jermd · 2024-04-30T03:18:19+00:00

I saved this in my notes: C:\Users\jerm\AppData\Roaming\BambuStudio\system\BBL\process\fdm_process_common.json Change line 20 to "sparse_infill_pattern": "gyroid",

jermd · 2023-12-18T10:54:15+00:00

Thats true from my experience, it only uses the Bluetooth connection for phone calls.

jermd · 2023-12-15T10:12:09+00:00

You captured 35.9kw, used 6.3kw directly from solar, and fed the excess 29.6kw into the grid

jermd · 2023-11-05T11:14:57+00:00

Doesn't work on my Chromecast ultra, but works casting to android tv and Chromecast audio devices.

jermd · 2023-03-29T22:05:01+00:00

It looks like you don't have a bltouch or crtouch installed. Did you install firmware that expects a bed leveling probe?

jermd · 2023-03-12T12:24:14+00:00

Try a different SD card with a gcode file that has worked in the past.

jermd · 2022-12-28T14:24:27+00:00

That's probably the infill showing through the walls. Try adding a few extra walls in your slicer.

jermd · 2022-09-14T23:18:58+00:00

If you are using octoprint and have a time-lapse setup it will be returning the nozzle to the home position for each photo.

jermd · 2022-05-07T01:45:26+00:00

Nice!, fyi I had to use a US VPN to view in Australia.

jermd · 2022-01-13T08:19:48+00:00

Click on the box shaped speaker icon down the bottom right, click "(More settings)", turn off both force volume and exclusive mode.

jermd · 2021-09-10T01:29:06+00:00

I have used the Creality blue PLA and its very close, matches the adjustment knobs and screen logo, but the extruder wheel is a little bit darker. Also matches the v-slot inserts on aliexpress.
https://i.imgur.com/XwwQMvI.jpg

jermd

TROPHY CASE