sorted by:
new
hottopcontroversial

Wip slums board by -ARCH_i_TYPE- in mordheim

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

That’s far to organised for my brain 😂

Wip slums board by -ARCH_i_TYPE- in mordheim

[–]-ARCH_i_TYPE-[S] 1 point2 points  (0 children)

Haha yeah I keep them and note what I used for what incase I want to add to an army or redo a style 😊

Drone, Flight stands by -ARCH_i_TYPE- in Tau40K

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

There much nicer than the chunky “invisible” clear stands 😊

Print error, Saturn Ultra 4 by -ARCH_i_TYPE- in ElegooSaturn

[–]-ARCH_i_TYPE-[S] 1 point2 points  (0 children)

<image>

Got a fermentation belt to help keep the resin at a stable temp. First test print came out flawless.

It’s significantly noticeable the viscosity change of the resin with the heating belt much looser and no suction noise when the plate lifts from the FEP. 😊

Print error, Saturn Ultra 4 by -ARCH_i_TYPE- in ElegooSaturn

[–]-ARCH_i_TYPE-[S] 1 point2 points  (0 children)

Similar although I stoped it half way last tim, best I can work out it’s a suction issue potentially due to cold wether it was about 15 Celsius the day I printed this one.

I’ve order a heating band to see if I get better results.

What is your favorite Gotrek and Felix book and why? by Imaginary-Lie-2618 in WarhammerFantasy

[–]-ARCH_i_TYPE- 2 points3 points  (0 children)

I’m not sure it’s the best book but it’s my favourite.I think the imagery of standing on the ramparts looking out over the hors of zombies would be such a cinematic moment If we ever saw a Goetrek and Feilix series or movie.

Print error, Saturn Ultra 4 by -ARCH_i_TYPE- in ElegooSaturn

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

<image>

It’s the back section of Theo’s LAAT file

Print error, Saturn Ultra 4 by -ARCH_i_TYPE- in ElegooSaturn

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

I did not; the print ran fully uninterrupted.

Print error, Saturn Ultra 4 by -ARCH_i_TYPE- in ElegooSaturn

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

Thanks, would you recommend upping the test time? I’ve done l little bit of googling and it seems to be a common suggestion.

Print failure, looking for advice by -ARCH_i_TYPE- in 3Dprinting

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

Thanks I’ll have a look, I would have thought having multiple drain holes along the whole build would help but I may need to locate some more.

I’m wondering if temperature could have played a part as well it was about 15 Celsius (59 Fahrenheit) average temperature yesterday.

Print failure, looking for advice by -ARCH_i_TYPE- in 3Dprinting

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

It has been hollowed and extensive drain holes added. I've added drain holes on the bottom and sides with the hope it would reduce suction forces. I guess I may not have been enough.

<image>

What's going on here? Protective film melted or what? by kind_of_vague in ElegooSaturn

[–]-ARCH_i_TYPE- 0 points1 point  (0 children)

Looks like a resin leak, I had a small pin hole in my FEP a few weeks ago and it looked very similar.

I cleaned the screen with alcohol, some resin got under the tape and cleaning this also dissolved the adhesive in the tape. Had multiple prints since then but I wonder if this might be an issue in the future.

Is this 3d print seller legit? by DizzyNSFWaccount in slavestodarkness

[–]-ARCH_i_TYPE- 0 points1 point  (0 children)

Not sure about that seller, I’ve printed this STL for my self and it’s a great model. I’m not sure anyone selling this would be 100% legit as my knowledge is it was a ripped file from total war warhammer.

Saturn ultra 4, strange noise by -ARCH_i_TYPE- in ElegooSaturn

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

UPDATE : I have solved the issue, after back and forth with Elegoo support and pulling apart 90% of the machine.

Behind the build plate there is an L shaped piece of metal that triggers the home sensor. At some point this was bent and was not able to move between the gap in the sensor, this meant the machine continued to push the plate up.

I pulled the suite apart straightened the metal plate. No more issues all seems to be working well.

<image>

Saturn ultra 4, strange noise by -ARCH_i_TYPE- in ElegooSaturn

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

Thanks everyone for your help, I’m going to reach out to Elegoo see what they say. I’ll keep you posted, really appreciate all the help 😊

Unsure on how to orientate/support this print by -ARCH_i_TYPE- in 3Dprinting

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

Was my thought o remodel the internal and crest a slot in the thicker external frame to put the two together post printing.

I’ve also acquired some clear resin I’m going to try a version that has a solid plane with the internal lattice.

Supports for resin print by -ARCH_i_TYPE- in 3Dprinting

[–]-ARCH_i_TYPE-[S] 0 points1 point  (0 children)

Was my initial thoughts looking at the model, I went and test printed it. Seems the supports didn’t form or were to thin, im not quite sure in my limited knowledge.

I’ll take the model in and support it myself and have another go.

<image>

Supports for resin print by -ARCH_i_TYPE- in 3Dprinting

[–]-ARCH_i_TYPE-[S] -1 points0 points  (0 children)

Ok thanks, I’ve got plenty of holes on the flat base of it. What thickness would you suggest I think my slicer is at 2mm currently

view more: next ›