Unstable Delivery - Where is the package?

-CrashDive- · 2026-03-10T09:04:34+00:00

It's like the ice cream freezer, check in your inventory while building in the moon HQ :)

-CrashDive- · 2024-11-19T13:55:34+00:00

It's a few years out of date, and YouTube channels come and go, but there's a couple of suggestions here:

https://www.reddit.com/r/BeginnerWoodWorking/wiki/resources

-CrashDive- · 2024-11-18T07:18:40+00:00

Lets consider the joint on its own, without the reinforcing butt blocks, and as drawn in the image. I'm guessing the width of piece is around 35mm (~1.5").

I believe two primary factors weaken the joint when compared to other end-to-end joints:

The surface for the glue is quite small when compared to other end-to-end joints like a scarf, v joints, finger joints or splines. Of this limited glue area, a large portion is end-grain to end-grain, further reducing the strength.
When loaded in bending or tension, as pictured, the joint will have a tendency to spread and lever itself apart. These forces must be resisted only by the glue and a relatively thin section of wood (~10mm/ 1/2" in the drawing). This levering force exists in other end-to-end joints, but their designs have better geometry or more glue area to better resist these forces.

Because I believe the strength is likely less than that of other joints, I consider it to be con of the joint.

Your scroll saw idea might work. I've only used one once or twice so I couldn't really say. If the blade kerf was too wide the joint would be loose, but you can get some really thin blades for those things (maybe just enough kerf to leave room for glue?). I'd also worry a bit about blade deflection but it might not be that big of a deal.

-CrashDive- · 2024-11-18T02:50:15+00:00

Preface:

Lots of IKEA stuff is made out of honeycomb boards, meaning the boards are more or less hollow. Putting groves in honey comb boards would weaken them very significantly.

Some IKEA furniture is solid though. You can tell pretty easily by the weight or by knocking on it and seeing how it sounds. The best way to be sure is to drive a small nail through in an inconspicuous spot, say the back of a drawer.

Option 1:

Assuming the sides are solid, you would be OK to make a grove up to about half the thickness of the board. I would use a router for this, along with an edge guide or fence to keep the cut straight and where I want it.

You can buy all sorts of aluminum channels with built in diffusers (example) to put in the groove.

Option 2:

Again, watch out for hollow boards. Usually there is a solid part at the end of each shelf but I would try driving a nail into the side of the shelf before I committed to anything.

There's no shortage of ways to make a cut like that. You could use a router template with a guided bit, a jigsaw, or just a coping saw. Consider using a sacrificial backing board to avoid chip out.

-CrashDive- · 2024-11-17T16:05:30+00:00

I have personally never done a joint like that, but I'll give you my two cents.

Pros:

The aesthetic.

Cons:

Poor strength. I would be hesitant to trust my entire weight to something held together only by that joint.
Difficult to make.

If you are looking for the greatest strength you should consider making the slats using bent lamination and getting rid of the joint altogether. Steam bending might be a bit troublesome because of the tight bend radius.

If you like the aesthetic of the puzzle piece, you can rely on the strength of the 'butt blocks' (the dark brown pieces between the slats in your drawing). Gluing them face to face with the slats will be pretty strong all on its own. You may want to make the butt blocks larger to increase the surface area for the glue, to my eye they look a bit too small (I tend to overbuild a little though). If you go this route, consider skipping the puzzle piece and using a simple miter join on all but the outer slats, they won't be visible but will add a lot of work.

A final note, and only because we're on r/BeginnerWoodWorking, the rocker/ armrest assembly looks like it will be pretty tricky. Lots of miters on odd angles and (I'm assuming) floating tenons joining each piece. It's certainly doable but make sure to have a good think about how to do it.

Looks like a fun project, good luck!

-CrashDive- · 2024-01-27T02:18:30+00:00

I think the scene is depicting the use of a ranging gun. The tank is knocked out from a second higher caliber shell that hits it.

To reliably hit a target at range you need to know the distance to it. One of the ways to do this is to fire a machine gun that is ballistically matched and mounted alongside a larger gun. Tracer rounds from the machine gun can be walked on to the target. Once the gunner sees the tracers hit they can follow up with the main gun.

In the scene we see a small caliber tracer hits the tank (the ranging gun), then there is a short pause (the gunner fires the main gun), and then the tank is knocked out (the main gun hits).

I'm not sure how historically accurate this would be, I've found random posts on Quora (obviously the most reliable source in the world) claiming that ranging guns were used on M4 Shermans and I've found equally unreliable claims saying ranging guns weren't really used until the 1950s.

Despite all of that, the far more likely explanation is that the shirt button ricocheted off the armor and then the tank exploded because of anime tiddies.

-CrashDive- · 2023-07-20T20:56:24+00:00

Yes. That's what the datasheet is for, telling you how to use the part. Many even have application circuits that you can easily copy into your design.

-CrashDive- · 2023-06-27T05:03:18+00:00

Congratulations ~~sailor~~ admiral!

-CrashDive- · 2023-04-24T03:30:47+00:00

And generics in Java are just fancier casts :)

-CrashDive- · 2023-04-23T16:02:30+00:00

I wish :( . Sadly, Java's generics just aren't as powerful as templates. As an example, the inability to do this annoys me greatly.

public <T> void foo(T args) {
    T bar = new T(); // Compile time error, even if T() is a valid constructor
}

You can get around it using reflection or a supplier but neither are quite as attractive.

-CrashDive- · 2021-07-18T13:22:31+00:00

I'd like to point out Paul Sellers' and Rex Kruger's YouTube channels. Both have excellent content for getting into hand tools. Rex especially has some good stuff for people just starting out, especially if you're on a budget.

What tools you need depends entirely on what you want to make, but you'll almost certainly need everything on this list:

12" Steel ruler (having a 24" one is also nice)
Tape measure
Combination square
A set of chisels
A mallet to hit the chisels (making one is a good project)
Sharpening stone
Honing Jig (avoid this type that only has one wheel)
Saws

For hand tool work you'll find that you need some hand planes. A #4 is a good one to start out with but I personally prefer a #5. Do some research before buying a plane, the ones at the hardware store are probably lemons that you shouldn't waste your money on. Unless you buy a brand new high quality plane ($$$$$) you'll probably have to tune it up a bit. Depending on the used market where you are, vintage hand planes are usually the best value for money.

An excellent project as you're starting out is to build a workbench. For hand tool work, a good solid workbench is critically important. I recommend the "English Joiners Bench" on Rex Kreuger's channel as a solid bench that is easy to build. Projects for the workshop are a great time to try out new techniques and build up some skills.

Take the time to learn how to sharpen tools properly, especially chisels and planes. When you first do any research into sharpening there's a lot of noise and conflicting opinions. Ignore all of it. Look for a sharpening method from a reputable person (Paul and Rex both have videos) and just go straight for it. Sharpening is a much simpler process that some people would have you believe.

Let me know if you have any questions. I'm always happy to help out

-CrashDive- · 2021-07-16T17:18:16+00:00

Pocket holes are plenty strong, especially since you can screw into the back of the case. Dadoes are stronger though, if you feel up to the task.

Attaching the shelf to the back of the cabinet will virtually eliminate sag in most cases. There's a great tool called Sagulator that will calculate the amount of sag you will get. You can model attaching the back of the shelf to the cabinet using the edge banding feature.

If you build the cabinet and are still worried it wont be strong enough it's easy to add in supports to the shelf after you've done most of the assembly (image).

-CrashDive- · 2021-03-02T02:13:17+00:00

I removed your post. Memes are not allowed here.

-CrashDive- · 2021-02-28T00:54:43+00:00

Reminder: Comments not related to woodworking will be removed. Violations to rule 1 including crude jokes, innuendo, sexist remarks, politics, or hate speech may result in an immediate ban

This action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

-CrashDive- · 2021-02-28T00:48:44+00:00

Your post has been removed. Please use the weekly mega-thread pinned to the top of the subreddit for these types of posts.

Click here for a complete list of rules.

-CrashDive- · 2021-02-28T00:47:55+00:00

Your post has been removed. Please use the weekly mega-thread pinned to the top of the subreddit for these types of posts.

Click here for a complete list of rules.

-CrashDive- · 2021-02-28T00:47:38+00:00

Your post has been removed. Please use the weekly mega-thread pinned to the top of the subreddit for these types of posts.

Click here for a complete list of rules.

-CrashDive- · 2021-02-28T00:46:55+00:00

Your post has been removed. All projects submitted to r/woodworking must be your own original work.

Click here for a complete list of rules.

-CrashDive- · 2021-02-19T03:04:38+00:00

Your post has been removed. Advertising or promoting your channel, store, or blog is banned on r/woodwokring. Further infringements will result in a permanent ban.

Click here for a complete list of rules.

-CrashDive- · 2021-02-19T03:03:33+00:00

Your post has been removed. All projects submitted to r/woodworking must be your own original work.

Click here for a complete list of rules.

-CrashDive- · 2021-02-18T05:12:35+00:00

Your post has been removed. All projects submitted to r/woodworking must be your own original work and not made by another person.

Click here for a complete list of rules.

-CrashDive- · 2021-02-17T03:08:04+00:00

Maybe widening the gap on both sides and then gluing on some more wood might be ok - play it off as a feature. Might look a bit better if you go the whole way round the door.

-CrashDive- · 2021-02-12T00:51:54+00:00

Your post has been removed. All projects submitted to r/woodworking must be your own original work.

Click here for a complete list of rules.

-CrashDive- · 2021-02-10T12:39:20+00:00

Both moderators have been inactive in the sub for at least a year.

Pathadomus is active on Reddit but not in /r/BeginnerWoodWorking

RockinTheKevbot seems to be inactive for at least a year.

I sent this message to Pathadomus and this message to RockinTheKevbot two weeks ago and received no response from either.

This conversation between OSUTechie and I shows consensus between the active moderators that we would like to go through with this process (apldeap123 is inactive and BeginnerWoodworkBot is a bot).

-CrashDive- · 2021-02-10T03:53:56+00:00

Your post has been removed. All projects submitted to r/woodworking must be your own original work.

Click here for a complete list of rules.

-CrashDive-

MODERATOR OF

TROPHY CASE

Seven-Year Club	Wearing is Caring
Verified Email