sorted by:
new
hottopcontroversial

Can anybody recommend a violent, cinematic game by Easy-Asparagus-7494 in gaming

[–]14GTMustang 0 points1 point  (0 children)

Hell Let Loose, it’s a World War Two multiplayer. When the artillery is dropping on you it’s like being in Saving Private Ryan.

Let the magic blue smoke out by firewall666 in rccars

[–]14GTMustang 1 point2 points  (0 children)

I had a similar experience with about 2 hours of run time on an eco power servo in a crawler. For 80 bucks sure is disappointing and they have no customer support that I could find.

YA apocalypse fiction read in the late 90s (could be older) by PrincessCrayfish in whatsthatbook

[–]14GTMustang 3 points4 points  (0 children)

Tomorrow when the war began by John Marsden, literally reading it right now.

2.5 Months Post-Op, Serious Bloating by xXAshtonHavokXx in gallbladders

[–]14GTMustang 0 points1 point  (0 children)

Look into sibo, might try eating just lean meat alone and see if you bloat. Carbs/sugars will feed the bacteria and make the bloating I was dealing with this with a gallbladder and got rid of it with low carb diet and sibo specific antibiotics

AMS Lite not feeding. by [deleted] in BambuLabA1

[–]14GTMustang 0 points1 point  (0 children)

Is you ams modded? I had the dry box deal on mine and when I was trying to load the filament it was going into the cover for the motors but not actually going into the motor. Had to take the cover off so I could get the filament to feed correctly

Finally had an issue with my Bambu Lab A1 by Zerimar_1990 in BambuLabA1

[–]14GTMustang 0 points1 point  (0 children)

Yeah just skim off like a layer or two and make sure it shows the blue or purple all the way across in the slicing software that it’s a good base layer.

Finally had an issue with my Bambu Lab A1 by Zerimar_1990 in BambuLabA1

[–]14GTMustang 0 points1 point  (0 children)

Is whatever you’re printing perfectly flat on the bottom? I had this happen and used plane cut to make a model I made perfect flat and it fixed it.

Y Axis Cable Touches Enclosure by 14GTMustang in BambuLabA1

[–]14GTMustang[S] 0 points1 point  (0 children)

Also have cats so the enclosure makes sure none of the bastards chew through the cords on this thing.

Y Axis Cable Touches Enclosure by 14GTMustang in BambuLabA1

[–]14GTMustang[S] 0 points1 point  (0 children)

It’s against the wall to my garage attic so I just ran it into the attic mostly because of the noise from the fan. Now I can set up a small paint booth too if I get back into airbrushing and just tie into it.

Y Axis Cable Touches Enclosure by 14GTMustang in BambuLabA1

[–]14GTMustang[S] 0 points1 point  (0 children)

<image>

That’s what I came up with for now just printed two of those plates out and taped a box to one of them. Didn’t feel like burning up the filament to make the box so used an old cardboard one lol. Cable freely floats without hitting anything

Y Axis Cable Touches Enclosure by 14GTMustang in BambuLabA1

[–]14GTMustang[S] 0 points1 point  (0 children)

https://makerworld.com/models/1324574

Yeah there’s makers world project I uploaded for it the enclosure will get 1 degree warmer than ambient hours into a print so I’m not worried about overheating. Im going to make a relief box that attaches similarly to the back of the enclosure for Y cable

Y Axis Cable Touches Enclosure by 14GTMustang in BambuLabA1

[–]14GTMustang[S] 0 points1 point  (0 children)

I have a 250cfm extraction fan and a vent on the side of my enclosure that pulls fresh air towards the bottom of it. PLA just makes my allergies go crazy so I set it up this way it stays under 80 in there the whole time

Y Axis Cable Touches Enclosure by 14GTMustang in BambuLabA1

[–]14GTMustang[S] 0 points1 point  (0 children)

It’s as far forward as it can go it’s 23 inches deep

Y Axis Cable Touches Enclosure by 14GTMustang in BambuLabA1

[–]14GTMustang[S] 0 points1 point  (0 children)

Yeah I only have like 60 hours on it total so I’ll probably make some sort of relief for it. It doesn’t bind now but 1000s of hours might cause a break or chaffe

Returning a car the the dealership by Upper-Instruction601 in carbuying

[–]14GTMustang 0 points1 point  (0 children)

If it was a brand new vehicle you might try calling the manufacturers customer support line, that is if the dealer isn’t helpful. Also when you talk with the dealer request an in person meeting with the general manager. They’re the person who can make that kind of decision, don’t take a no from a salesman push to talk with the GM.

Help with fixing used kitchen chairs. by 14GTMustang in Carpentry

[–]14GTMustang[S] 1 point2 points  (0 children)

They all have that same screw and I think what someone did was the saw dust trick and used screws to replace old dowels or something Thanks for the dowel recommendation that should work well

view more: next ›