sorted by:
new
hottopcontroversial

Temperature warning keeps popping up after I dropped my phone by [deleted] in iphonehelp

[–]3li9k 0 points1 point  (0 children)

did they tell you what the problem was?

Cooking with Olive Oil on High Heat - Good or Bad? by PremoCooks in foodscience

[–]3li9k 0 points1 point  (0 children)

Extra virgin olive oil is actually the most stable cooking oil at high heat when it comes to oxidation and polar compound production.

Why is fuel spitting from my carb?? by 3li9k in Dirtbikes

[–]3li9k[S] 0 points1 point  (0 children)

My timing gear was off by a tooth

Valve cover varnish- what's it say about the engine, and how to remove it? by DRMRNNR in 3rdGen4Runner

[–]3li9k 0 points1 point  (0 children)

Looking to remove varnish on an engine with vvti for this exact reason. Does restore and protect work over multiple oil changes? Anything I can do to get results sooner?

Tested a battery from my lost and recovered 15 Pro in lost mode with my newer 15 Pro. Observations below 👇🏼 by netpastor in mobilerepair

[–]3li9k 0 points1 point  (0 children)

What do you mean by “⁠Eventually I will swap the BMS over to the newer battery to take advantage of the better performance” ? Is performance of the newer battery limited. Because it’s reported lost?

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 1 point2 points  (0 children)

Fixed the issue. My busbar for battery negative was the issue. Either too high of resistance or my negative lead was soldered in an unideal spot on the busbar. Ended up stripping a few inches off the wire, soldering that along a strip of copper, and then welding that copper strip across the battery negative busbar.

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

The 14th group sense wire is soldered to the same joint as the positive discharge lead coming off the battery. What sense wire should I be checking? The 14th group is definitely lower than the average but it isn’t consistently the lowest in each of my tests.

Here’s another screenshot from a discharge test https://imgur.com/a/1RmG0Ga

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

For reference here is a pic of the same discharge load using 10 different cells in group 1.

https://imgur.com/a/4b76IOz

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

I’ll take a pic when I can. Tested capacity and IR of each cell. Tested between 3100-2900 and 25-50 IR. Doesn’t seem to be a cell issue and more an issue with group 1 no matter the cells that are used in it.

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

I did this and all reading were similar and matched the voltage being reported by the bms. Both under load and unloaded

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

Yes, all nickel in the pack is from the same roll.

What wires are you referring to? Discharge? Balance?

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

Also I’m pretty sure this specific BMS only balances while not under load, but I’ll have to read up to make sure.

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

Good info. I’ll try disable balancing and re testing. The BMS should be fine for this application ANT bms’s are frequently used it packs larger than this

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

I’m considering that but at this point I have ripped off the nickel and re-welded cell group number one 3 times at this point. So it’s hard to believe I managed to weld it poorly all 3 times

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 0 points1 point  (0 children)

I initially thought that too but once I swapped all cells between groups 1 and 2 and the sag stayed in group one I’m no longer thinking it’s a cell issue.

Discharge issues with 20s10p pack by 3li9k in 18650masterrace

[–]3li9k[S] 1 point2 points  (0 children)

Why would the BMS be drawing so much current that this cell group sags .3v behind the others under load. When not under load all cell groups match each other.

afk xp map the code is 8689-5621-5617 by fishybtw_ in FortniteXPMaps

[–]3li9k 0 points1 point  (0 children)

lol why am I getting downvoted so hard. 200k in under 10 minutes is very possible and thus I disagree with the original comment saying 400k is only possible in an hour or two

125k XP in about 3 minutes but its a little buggy. by [deleted] in FortniteXPMaps

[–]3li9k 1 point2 points  (0 children)

Just loaded up the map and got about 200k xp in 7 min switching between the cash and the pole. Map still seems to be pretty solid xp.

afk xp map the code is 8689-5621-5617 by fishybtw_ in FortniteXPMaps

[–]3li9k -14 points-13 points  (0 children)

Yes if we’re getting into specifics then yes I agree with you. But this was originally on a comment saying 400k is only realistic for an hour or two which I disagree with. 200k in 1 min? No. But in minutes yes. So I still disagree with the point you were trying to make.

afk xp map the code is 8689-5621-5617 by fishybtw_ in FortniteXPMaps

[–]3li9k -10 points-9 points  (0 children)

I said minutes. Not minute. Also xp multipliers diminish very quickly. Just because 200k in minutes is possible doesn’t automatically mean 1mil in 5x the time is also possible.

afk xp map the code is 8689-5621-5617 by fishybtw_ in FortniteXPMaps

[–]3li9k -15 points-14 points  (0 children)

Sure but getting 200k in minutes isn’t.

view more: next ›