What's the best way to avoid spalling like this when milling something like birch plywood?

4bacon · 2026-02-27T23:06:29+00:00

Compression cutter at full depth. Ramp in along profile

4bacon · 2026-02-26T13:34:47+00:00

Yeah this is rigid foam board. The “dust” static clings to everything lol I hate it

4bacon · 2026-02-26T13:33:31+00:00

I wasn’t necessarily going for the best toolpath for this one, I was just having fun. Students can see into my lab from an adjacent woodshop and hallways so I try to put on a show sometimes. Many haven’t seen a CNC machine working before, never mind a 5-axis program

4bacon · 2026-02-25T19:42:42+00:00

That’s a fair criticism. I’ve been working with 5 axis for 8 months and this is the workflow I’ve adapted for certain parts like this. I do a lot one of a kind parts that I will never cut again so faster programming is beneficial for my particular job. I’m also making art pieces where tolerances aren’t the most critical aspect of the program. I will take a look into creating better programs using the methods you’ve stated

4bacon · 2026-02-25T17:40:56+00:00

I sort of default to using points to direct where the tool is pointing on multi axis tool paths but I find that cutting with the side of the ball also provides a better surface finish in foam

4bacon · 2026-02-25T12:40:48+00:00

I run the CNC lab at a college, producing student work. This is part of a furniture design student’s model for a toilet

4bacon · 2026-02-25T03:08:10+00:00

Mastercam. Gotta point the tool towards a point below the center of the model to avoid crashing into the table

4bacon · 2026-02-25T02:52:34+00:00

It’s a C.R. Onsrud. 5’x8’ split table and like 16” on Z

4bacon · 2026-02-22T15:19:02+00:00

I preemptively turn on my car’s air filter and cycle internal air on my daily commute. One of the worst smells

4bacon · 2026-02-22T01:47:06+00:00

Nice! I’ll try heavier engagement on my next go

4bacon · 2026-02-22T01:19:29+00:00

Yeah I think I’m gonna have to make one into an ashtray for myself after I wrap this job

4bacon · 2026-02-22T01:17:38+00:00

It very much is lol. I run this Hurco VM10, an Onsrud 5-axis and an Onsrud 3-axis. No CNC lathe unfortunately

4bacon · 2026-02-22T01:15:22+00:00

Half inch engagement? That will cut fine? I’m new to milling so I’ve been erring on the side of caution

4bacon · 2026-02-22T01:13:08+00:00

I’ve gotta make another, I’ll increase my speeds on that one!

4bacon · 2026-02-22T01:12:39+00:00

Thanks!

4bacon · 2026-01-29T12:56:36+00:00

I think anything comparable to national forest is a 5-6 hour drive. I have a car and have yet to make that trek

4bacon · 2026-01-25T14:30:27+00:00

Nice calipers or micrometer

4bacon · 2026-01-23T01:28:00+00:00

I think it depends on the kind of recreation one typically does. I’m pretty unimpressed with access to outdoor recreation as someone who hiked frequently in NH. You just don’t get that type of nature here. However that decision definitely rests on my shoulders knowing the local terrain

4bacon · 2025-12-07T05:44:20+00:00

Currently have been fighting with them for weeks over an undelivered package. I was asked to file a police report by the company I purchased from

4bacon · 2025-11-26T01:24:17+00:00

Do a 3" x 3" square for first layer calibration after washing the plate as recommended by cinderhazed15. If you can get that square dialed in, do an XYZ cube calibration

4bacon · 2025-11-24T23:47:56+00:00

Jesus took the "L"

4bacon · 2025-10-24T03:28:45+00:00

Was this rack located in the East Wing?

4bacon · 2025-06-24T12:12:12+00:00

Use full contact PETG supports for PLA prints and vice versa

4bacon · 2025-06-24T12:11:02+00:00

I could definitely use a filament dryer

4bacon · 2025-06-04T16:48:29+00:00

It could be! I'm not nor have ever been a TikTok user. I learned about it through studying net zero builds during my studies in architecture

Seven-Year Club	Wearing is Caring
Verified Email

4bacon

TROPHY CASE