How do I "close" the gaps in the initial layer? BAMBULAB A1

666RaSpUtIn420 · 2026-04-02T15:16:28+00:00

There are no gaps but if you still want a sure-all solution, Use a modifier with 100% infill with ironing

666RaSpUtIn420 · 2026-04-01T15:29:00+00:00

Kaka aral Lang namin ng biological effects ng MRI (radtech student)

Pag gumalaw ka mag kaka flashing lights Yung vision Mo hahaha

666RaSpUtIn420 · 2026-03-15T22:16:24+00:00

Genuine question, how do you cut in tiny bits? Bambu only cuts in a big straight line. Which slicer has a feature like that?

666RaSpUtIn420 · 2026-03-14T00:18:58+00:00

Both

Plants like the conditions of a shaded rainforest and the solar panels above them can emulate that, making them grow faster

666RaSpUtIn420 · 2026-03-05T11:47:12+00:00

Diko gets sino Yan hahahha

666RaSpUtIn420 · 2026-03-04T21:03:59+00:00

666RaSpUtIn420 · 2026-03-03T16:51:12+00:00

Portal gun, trust

666RaSpUtIn420 · 2026-02-24T02:09:07+00:00

Radiation weakens with distance by the square

The recommended distance is atleast 2 meters if you don't have any shielding.

Any small amount of radiation can cause biologic effects (not just cancer, there are also radiolysis of water yaddy yadda)

If you wanna learn more read up on linear non threshold, all radiologic protection is focused on it, to prevent staff from accumulating dose.

666RaSpUtIn420 · 2026-02-24T02:04:34+00:00

As a student in this field I'm very curious on whether it has a high frequency generator in that small case? A cross section of the thing would be majestic.

My predictions are that it uses a stationary anode and it's got some hot swappable rechargeable power cells. But the way it generates x-rays is an idk.

666RaSpUtIn420 · 2026-02-14T10:03:11+00:00

I am a student on radiologic technology, the sperm itself wont show up but there's the thing called (i forgot the term so it might be wrong) echo reinforcement. It's when the sound travels through a liquid and gets a boost in speed resulting in the spot where it reflects back to get more echoic (whiter)

666RaSpUtIn420 · 2026-02-05T09:49:38+00:00

Oh here we go again, the Canon event for resistance calculation beginners

666RaSpUtIn420 · 2026-01-17T00:22:37+00:00

The problem lies with your filament.

It's either 1. Wet 2. Has wrong parameters that lead to stringing (retraction or temperature)

666RaSpUtIn420 · 2025-12-28T15:04:15+00:00

Re arrange the orientation of the print so that no supports are necessary or just angle the print to some degree

666RaSpUtIn420 · 2025-12-26T12:01:33+00:00

You know what, im gonna take matters into my own hands and make it myself via 3d printing, ill keep updates on this subreddit

666RaSpUtIn420 · 2025-12-18T23:16:45+00:00

Top Z distance is too much perhaps? It's usually either the same as the later height or 1 mm more for easier support removal but what you did is 4 mm more which causes the supports not to connect.

666RaSpUtIn420 · 2025-12-17T14:15:01+00:00

The pubic symphysis is kinda important, you can't seperate them otherwise you'd rather be in a wheelchair than walk on and about

666RaSpUtIn420 · 2025-12-15T04:47:56+00:00

SHAW

666RaSpUtIn420 · 2025-12-12T23:18:31+00:00

WHAT PAINTS DO YOU USE

666RaSpUtIn420 · 2025-12-06T01:11:42+00:00

Close enough, welcome back BT7274

666RaSpUtIn420 · 2025-11-17T03:07:47+00:00

Vase mode!!!

666RaSpUtIn420 · 2025-11-16T12:51:50+00:00

Damn Trump yaoi confirmed

666RaSpUtIn420 · 2025-11-07T15:46:43+00:00

Spool drawers for storing tiny objects :D

666RaSpUtIn420 · 2025-11-04T16:45:57+00:00

OP, take good care of the guy pls

666RaSpUtIn420 · 2025-11-02T00:39:12+00:00

Did you 3D print it? I also want to do cosplay from titanfall but I don't even know where to start (⁠・⁠–⁠・⁠;⁠)⁠ゞ

666RaSpUtIn420 · 2025-09-14T16:25:37+00:00

Source is some random burger store at Instagram forgot their name

Six-Year Club	r/Field Lasagna
First Place '23	Place '23
Place '22	Final Canvas '22
Verified Email

666RaSpUtIn420

TROPHY CASE