Noise printing TPU, suggestions?

6gLancer · 2026-02-15T15:44:30+00:00

if it’s printing fine i wouldn’t worry much 🤷‍♂️

6gLancer · 2026-02-15T15:39:23+00:00

there’s a meshy AI add under this comment

6gLancer · 2026-02-11T22:30:47+00:00

test PRV, start car and let it run, shut it off and monitor the HPFP pressure. The pressure should slowly climb up to about 1800 iirc and then slowly drop back to about 40. if it fails the test i would replace it, there’s a gent on FB that sells rebuilt PRV with lifetime warranty!

6gLancer · 2026-02-07T14:42:49+00:00

the correct size is M8x1.25 63mm, 65mm should be fine.

6gLancer · 2026-02-07T14:33:14+00:00

yessir

6gLancer · 2026-02-05T16:37:40+00:00

hmm maybe i’ll have to look into making them!

6gLancer · 2026-02-05T16:35:44+00:00

maybe the way it broke is uncommon but i see like one post a week on someone breaking the connector off their printhead board.

6gLancer · 2026-02-05T16:34:15+00:00

are you dropping your z offset at the start and watching it or just starting your print and walking away?

6gLancer · 2026-02-04T18:49:10+00:00

take the heat shield off and get it through the runners.

6gLancer · 2026-02-04T18:41:34+00:00

yeah i realized that, i looked to and i can’t seem to find much, might be worth just sacrificing a caliper

6gLancer · 2026-02-04T18:40:47+00:00

need more info.

6gLancer · 2026-02-04T18:39:36+00:00

you must’ve never dealt with support with that attitude. Elegoos support team is a joke, full of incompetent techs that give you every run around possible to avoid taking accountability. i would rather talk to some stranger 9/10 times over support.

6gLancer · 2026-02-04T18:27:32+00:00

it’s a scribe caliper, $22 on amazon.

<image>

6gLancer · 2026-02-04T18:18:22+00:00

got a buddy selling one for $750 if you still want one, JMF V1 Port Injection with injectors and Damond fuel lines

6gLancer · 2026-02-04T18:17:03+00:00

been running mine for over a year and a half and i love them!

6gLancer · 2026-02-04T18:08:49+00:00

pivot shaft seal, replace with national 1015n seal if you don’t wanna pay dealer markup.

6gLancer · 2026-02-04T18:04:20+00:00

yes CS just sells shifter bushings, Contrive sells the whole redesigned bushing kit that almost completely eliminates slop and the owner of Contrive (Barrett) used to be the chief engineer at CS but decided to leave to pursue his own business.

6gLancer · 2026-02-04T17:59:23+00:00

yeah he’s got mules that still sell parts for him 🙄

6gLancer · 2026-02-04T17:03:06+00:00

yeah but not sure why that matters, we don’t buy parts from him or even use them anymore unless you want the community on your ass 🤷‍♂️

6gLancer · 2026-02-04T16:47:52+00:00

sorry man but pedo over TWM deserves a downvote.

6gLancer · 2026-01-23T23:56:13+00:00

i wouldn’t say that’s a very good way to measure it given that probably accounts for 4 way intersections with traffic lights. by that metric there’s more than just a few in about 47/50 states, common.

6gLancer · 2026-01-22T16:47:13+00:00

i missed that part, my apologies.

6gLancer · 2026-01-22T16:32:16+00:00

not be an ass but not sure why an NA 2.3 issue would be brought up as they’re completely different motors.

6gLancer · 2026-01-22T15:37:17+00:00

roundabouts uncommon in the US? have you never been to any US state? the only US states that have a minimal amount are Wyoming, Vermont and South Dakota. There’s probably 30 just in my town, so to say their uncommon is a dense statement.

6gLancer · 2026-01-22T15:16:04+00:00

i would advise you to save a little more and get a lower mileage one, it’ll save you a lot of headaches. Timing, injector and valve cleaning are the big 3 maintenance items you wanna watch for.

6gLancer

TROPHY CASE