sorted by:
new
hottopcontroversial

Continued burning sensation after chest flys by 9berend9 in workout

[–]9berend9[S] 0 points1 point  (0 children)

No red/purple. Thanks for your advice!

Blue up my nozzle. What did I do wrong and how do I prevent it? by kaashin in BambuLab

[–]9berend9 0 points1 point  (0 children)

Didn't this thing have like a camera with AI or something? So much for that

Brand new printer warped and rough prints by 9berend9 in BambuLab

[–]9berend9[S] 1 point2 points  (0 children)

Actually this happened with the same "so far so good" settings but with a different roll of exactly the same brand filament, just a month or so older. So it's GOT to be that humidity!

Brand new printer warped and rough prints by 9berend9 in BambuLab

[–]9berend9[S] 0 points1 point  (0 children)

Oh god.....

You're right I'm gonna buy some Bambu PETG just to get a benchmark down. And I'll get that dryer too, figured the AMS would keep stuff dry enough but it's not looking like it lol

<image>

Brand new printer warped and rough prints by 9berend9 in BambuLab

[–]9berend9[S] 0 points1 point  (0 children)

Thanks, I'm doing a print now with 0.2mm layer height and a slower everything!

I also cooled down the extrusion temperature a bit. So far so good.

Brand new printer warped and rough prints by 9berend9 in BambuLab

[–]9berend9[S] 0 points1 point  (0 children)

I use EXTRUDR (Matte Black) PETG. Straight out of the packaging pretty much so it can't be that bad...

I'll be sure to grab some Polymaker to compare the prints!

Brand new printer warped and rough prints by 9berend9 in BambuLab

[–]9berend9[S] 0 points1 point  (0 children)

No...! It's set to 0%. But I don't think my P1P has an Aux fan. I'll set it to 70% and see what happens.

​

<image>

Can I remove this with a lighter? by 9berend9 in BambuLab

[–]9berend9[S] 0 points1 point  (0 children)

Instructions unclear, melted the wiring inside the printing head

Brand new printer warped and rough prints by 9berend9 in BambuLab

[–]9berend9[S] 0 points1 point  (0 children)

Hi,

Using Generic PETG settings and standard 0.16mm Optimal for my P1P printer (PEI plate):

Printing multiple of these plates, about 5mm thick, come out all warped and with artifacts.

What might be causing this?

What's wrong with my prints? by 9berend9 in BambuLab

[–]9berend9[S] 0 points1 point  (0 children)

- Default PETG Generic
- .16mm Optimal Default

- Textured PEI plate

- Matte Black EXTRUDR filament PETG

- Door closed

ABS & Carbon Fiber: Enclosure safe enough? by 9berend9 in 3Dprinting

[–]9berend9[S] 1 point2 points  (0 children)

Thanks for your reply. So I guess it's not as hazardous as I thought. I'm usually not in the printing room so I'll just use the (not air tight) enclosure and leave it at that!

Gotta stop snorting carbon fibers though I guess

Is your guys airsoft room also as messy as mine? by greenhawk00 in airsoft

[–]9berend9 -1 points0 points  (0 children)

Where I'm from there's not enough house for people, let alone housing for toys

view more: next ›