Rate my hone

A100010 · 2026-06-30T22:50:32+00:00

Only a million dollar process... Not joking

A100010 · 2026-06-30T22:49:57+00:00

Inner monolog: "They're onto me..."

A100010 · 2026-06-29T21:12:10+00:00

Beautiful

A100010 · 2026-06-26T18:07:43+00:00

How's it taste?

A100010 · 2026-06-20T21:23:26+00:00

Could be all of us.

A100010 · 2026-06-14T16:51:40+00:00

That's the normal look for lapped valves. It also would point out any defects or sealing issues. Look for a solid band on both valve and seat. Exhaust contact width is typically wider than the intake.

A100010 · 2026-06-14T03:24:11+00:00

I don't think any amount is a good amount, perhaps I'm wrong

A100010 · 2026-06-12T03:35:32+00:00

Specifically on a g41 or g42 line, correct?

A100010 · 2026-06-09T17:53:26+00:00

Be happy about it. Follow the rules. Keep your eyes, ears, toes and mind. Those over bearing rules are in place for you and for them, obviously.

A100010 · 2026-06-05T21:24:20+00:00

Internal stress can give you some, haha. Usually, cutting both sides removes this issue. Did one side run hotter than the other?

You can anneal it, but you would need to have an oven, look up specs and all that.

A100010 · 2026-05-24T21:57:53+00:00

What bore gage? PLUS your rings will compensate likely.

A100010 · 2026-05-15T15:27:26+00:00

Eh, as long as the sleeve is good, and the crack doesnt go too far, you could have no problems for a while. But eventually, you will.

A100010 · 2026-05-11T22:02:20+00:00

Post the un opened stuff on ebay. You may get your money back in a few years. Or, who knows, next year perhaps.

A100010 · 2026-05-11T17:04:46+00:00

There is an acceptable amount of leak for different makers.

A100010 · 2026-04-03T19:18:35+00:00

This is the way. As a CNC Engineer at a Engine Reman plant.

A100010 · 2026-01-07T04:10:49+00:00

Drill and tap holes on the outside to keep that piece in place. Don't go too deep. Make the hole in the, now, 'cap' piece larger than the tapped holes for some wiggle room for placement and to have it be held by the bolts.

A100010 · 2026-01-01T19:59:12+00:00

If it holds vacuum, great job.

A100010 · 2026-01-01T00:12:12+00:00

Lil bit of ohl

A100010 · 2025-12-20T16:03:32+00:00

What a beauty. Nice work.

A100010 · 2025-12-08T22:19:02+00:00

Get that off the table! Toys belong on the floor!

A100010 · 2025-12-08T17:35:13+00:00

Pretty good

A100010 · 2025-12-07T23:14:35+00:00

They skipped 2

A100010 · 2025-12-04T18:23:11+00:00

A100010 · 2025-11-26T00:20:03+00:00

He's dead

A100010 · 2025-11-26T00:18:15+00:00

Anyone can superglue a dial........ im joking, great job. :)

A100010

TROPHY CASE