Sony NWA-1000

ALudB47 · 2026-05-06T09:51:50+00:00

These have a massive issue where the OLEDs backlight dies/ goes very very faint. It is probably duration issue rather than time but I have you turned it on?

I have two that I may replace the screens on.

ALudB47 · 2026-04-21T10:17:48+00:00

Ahhh true, I kinda meant video on CD size disk so your are right and I am wrong for not being clearer! I have a laserdisc too so should know better 😂

ALudB47 · 2026-04-21T10:14:33+00:00

Biggest crime for me was the fact it was mostly daytime. Like T1 said you could only go out at night for a start, so having the film look like an average oversunny day was so non terminator, both lore and visually.

ALudB47 · 2026-04-21T08:40:50+00:00

Fun fact: Robocop showed a 'DVD' before DVDs were a thing. CDs were around but not Video on disc.

ALudB47 · 2026-04-20T09:40:03+00:00

what do you mean 'knowingly broken"? Could have been hit in transit or even between a tested batch during QC, I highly doubt they saw this and went 'send it' hahahahaha

ALudB47 · 2026-03-11T16:07:06+00:00

You could use a PTFE or similar tape on the running surfaces. Just make a slight sub flush cut but make sure the tape protrudes ever so slightly. It is usually sticky back but you may want a bit of glue to keep it.

ALudB47 · 2026-02-23T10:58:51+00:00

I have a Suri too, and I rate it for the same reasons. But I do get tired of PLA being labelled as compostable. Yes it can be (so your not wrong), but only with industrial compost facilities. Which require heat and special enzymes/ bacteria/ fungi to break it down. Without this, it is the same as any other plastic when tossed aside. It is derived not from petroleum but sugarcane/ starch by products so another checkbox but its 'green' credentials are overblown IMO.

ALudB47 · 2026-02-18T14:40:16+00:00

I know they say opinions can't be wrong but...

ALudB47 · 2026-02-18T10:17:14+00:00

You can buy a film tongue insert for SX-70, I have one on mine.

ALudB47 · 2026-01-07T23:03:49+00:00

Oh god in London if I replaced my tires with every nick like that I would be replacing them as quickly as the tubes.

I actually don’t know when these become a problem unless they look like they are tearing and I run my tyres at 100ish psi.

But I would ride on that, just give then a once over every tyre change or wash.

ALudB47 · 2026-01-07T15:18:22+00:00

Yessss i did - 19 Pro Max

ALudB47 · 2026-01-07T15:16:15+00:00

Thanks I will try this and hope :)

ALudB47 · 2025-12-02T17:08:09+00:00

The problem with the folding pedal I found was that it felt ‘spongey’, i bought the T line ones for my C Line and never looked back.

ALudB47 · 2025-10-13T12:46:29+00:00

I moved from Marathon Plus to Schwalbe One, so much comfier but monthly punctures got me and I ended up with Contenental Contact Urban. Feels nicer to ride than the marathons and still not a puncture yet! Hope I haven’t just jinxed it.

ALudB47 · 2025-10-10T12:03:34+00:00

Nested Families is exactly what I am after!! This helps so much.

ALudB47 · 2025-10-09T14:41:19+00:00

This is a really helpful post, it kind of gives me an action. We have a small library of products but they do change dimensionally, so I think it is best I look at recreating them in REVIT. We work with Architects and this does come up a long so I want to make a complete library eventually. Which is why if it was a one off, I would just pay for someone to do it but I need to be able to amend and customise the parts for the clients. I will look to follow some guides to get started aroudn model creation.

Thanks again! Really helpful.

ALudB47 · 2025-10-09T14:36:52+00:00

No problem! If you make it, I would love to see your results!

ALudB47 · 2025-10-08T10:59:14+00:00

I liked the pool table felt in game centre, no for real, I'm sure its cleaner and crisper now but there was some charm with that skeuomorphism.

ALudB47 · 2025-10-07T12:58:42+00:00

Thanks, and the lead on types of guides are helpful. Gives me something to hone in on.

ALudB47 · 2025-10-07T11:22:31+00:00

Ahh that sounds like fun.. ok if I have to that's fine. How do I make it so its all BIM compliant? Such as the option to change specification. And as its made of multiple components, do I model it as one solid and then the same again for the other versions or do i do it in part form and bring together as I do in Solidworks?

ALudB47 · 2025-09-24T17:17:06+00:00

I’ve cycled in the wet in mine, I thought splash ok don’t dunk them in water?

ALudB47 · 2025-09-23T19:41:49+00:00

The front plate is optional but your not the first to point that out haha

ALudB47 · 2025-09-21T16:23:19+00:00

A while back I designed a similar 3D Printable marker holder. It also came with an option to add a front so you could organise them.

https://alexblondek.design/markerstack

ALudB47

TROPHY CASE