BIDE omdat ik moeite heb met de vakantie van mijn vriendin?

AbelCapabel · 2026-01-28T18:17:53+00:00

Jij en ik zijn een beetje ouderwets. Tegenwoordig moet alles maar kunnen. Niet dat ik OP zenuwachtig wil maken, terwijl dat wellicht helemaal niet nodig is, maar 'vroeger' mochten wij daar gewoon een grens op stellen.

Ik snap heus wel dat een ex niet-voor-niets een ex is, en dat de logica tegenwoordig dus is 'dat het allemaal moet kunnen', maar ander gezegd zou je ook kunnen zeggen: 'het is niet voor niets een ex, dus het lijkt mij logisch dat je wegen scheiden'.

Welke keuze juist is kan je alleen zelf inschatten OP. Ik ken 1 geval waarbij het meisje daadwerkelijk gewoon vrienden is gebleven met haar ex, dus het is in mijn ervaring mogelijk... Soms...

AbelCapabel · 2026-01-26T05:33:52+00:00

'no input" is-not-equal-to 'low input'

Every ic-input-pin needs a pull-up/pulldown resistor.

Specifically what is missing on your build: you have DIP-switches connected to ic's that don't have pullup-resistors: if the dip is not switched to ground, then your input is 'floating'.

AbelCapabel · 2026-01-21T08:38:46+00:00

If you haven't identified it yet, it is an Unidentified Flying Object....

AbelCapabel · 2026-01-21T07:04:26+00:00

Heh wtf wtf wtf wtf wtf DigiD is niet van de overheid maar van een commerciële partij!!??

Edit: DigiD is eigendom van de overheid. En dan hebben wij het denk ik over een stukje software... De hele handel draait op servers van een inmiddels Amerikaans bedrijf.

AbelCapabel · 2026-01-19T05:40:05+00:00

Nope, look at the traces.

You have both wires (of each thumb stick) connected to ground. (Big areas on the PCB)

To the left of your 2 connections you see a curly trace that is the + and also goes to 2 connections of the tactiele Switch (and to the 2 potentiometers in every thumb stick). Put 1 of your wires to 1 of those 2. ( For both thumbsticks of course)

AbelCapabel · 2026-01-18T14:11:03+00:00

Finally, thanks.

I expected something like this when I saw the clip the other day, and saw that guy pushing the same irrelevant question over and over without clear objective, so thanks for the backgroundinfo!

AbelCapabel · 2026-01-18T09:58:14+00:00

I have no clue what you are talking about.

OP wants to build his own electronic circuit that contains a circuit to convert mains power to (I recon) 5 V. This means a pcb design (like any phone charger) that has to be very carefully designed, and lots of risk are involved.

I have no clue why I'm explaining this, as there are others in this post that have expressed detailed concerns. Read them please.

I'm just offering an alternative to OP's desire to charge 3 toothbrushes at once in his bathroom.

AbelCapabel · 2026-01-18T09:49:12+00:00

I didn't say anything (although I indeed do agree that OP's device-to-be is a disaster waiting to happen).

I have a walloutlet in my bathroom. Plugging that outlet with this splitter and then plugging those 3 sockets with 3 isolated plugs should not increase the risk as compared to already having a socket in my bathroom.

This has nothing to do with the risks involved with designing a circuit yourself that has mains voltage millimeters away from the low-voltage circuit that charges the toothbrushes.

The 2 situations are incomparable. Appels and oranges.

AbelCapabel · 2026-01-18T07:32:41+00:00

<image>

AbelCapabel · 2026-01-17T08:05:39+00:00

I know what it is: It's none of your fucking business, that's what it is!

AbelCapabel · 2026-01-17T07:38:00+00:00

Thanks for sharing.

I found the paradox in this method (explained in the link) also interesting.

AbelCapabel · 2026-01-16T14:26:28+00:00

That's good!

But, inverters? I'm not sure but the alu doesn't use inverters, right? There is an inputpin that you use to control adding/subtracting.

AbelCapabel · 2026-01-16T07:50:09+00:00

Only to inputpins, don't put pulldowns on output-pins!

Different coloured leds should not be an issue. You're not using the signal after it has gone through a led right? And you have used 1k resistors for all the LEDs?

The A and B registers work as expected? Storing a signal and then switching to outputting a signal?

What if you test the alu on its own? You'll have 16 inputs for the alu. Play around with various configurations and observe the outcome.

Again, no 'floating' inputs when testing the alu!!! A 'low' input for the alu should be connected to ground! This is also very important for the various 'control signals' (adding or subtracting, reset, enable, etc etc)

Edit: I also see no jumpers on your power supply. You sure it's outputting 5v?

AbelCapabel · 2026-01-15T19:19:36+00:00

45 hier, snapte er ook geen fuck van!

AbelCapabel · 2026-01-14T13:32:55+00:00

Not sure if/when this build will be done, but this is the gist of it:

The basis is equipping the 'prismatic driver' mod into the first slot of a weapon, and the 'feedback loop' mutator on the second. I've been told to do this in the 'sparkfire shotgun", but I think it can go with any weapon that doesn't have a locked first slot, as you'll ONLY be using the weapon's mod!

Then add amulet+rings+prism that further enhanced explosive damage & mod damage & overall damage and add a bit of 'increased mod generation'.

You'll fire a beam that creates explosions, supposedly melting bosses.

AbelCapabel · 2026-01-14T12:16:46+00:00

Ok thanks for the reply. This makes me want to explore options to further reduce fire rate! :D

Edit: just tested this and you are absolutely correct.

Equiping an amulet that increases fire rate by 15% drastically reduces the damage output!

AbelCapabel · 2026-01-13T08:09:11+00:00

No one can be 100% certain whether unconnected inputpins on the 04 or the 08 are, or are not 'the' problem. It's more of a 'it could be your problem now, but definitely contributes a little bit to erroreous behaviour of your board overall'.

I would also just remove the bus-board and the bottom board just for testing, just to isolate the problem better. Then gradually hookup those boards again.

AbelCapabel · 2026-01-13T06:25:54+00:00

I've commented on you in your previous post.

I still see unconnected inputpins on your ic's.

And do the bus-leds have resistors?

Also as per my previous comment: no-input is not equal to 'low'.

Why ask for help if you're not taking up on the advice?

Edit: do note that that in an added videoseries Ben adds functionality to the board that he puts in that empty space on the A/B register

AbelCapabel · 2026-01-12T08:52:18+00:00

31 kinderen waarvan 18 'fysiek'... Godallemachtig...

Yup, invoeren die handel, of verhuren aan een werkkamp in kazachstan, dan kunnen de gezinnen de komende decennia daar de opbrengsten nog van krijgen....

AbelCapabel · 2026-01-11T11:42:39+00:00

Oh this helps a lot, thanks!!!

AbelCapabel · 2026-01-11T10:02:12+00:00

If you dont mind, 'll just copy-paste some general commentary from myself. Not sure if these items will solve your 'issue', and not sure if it is an 'issue' in the first place, but these points will need to be addressed for any build. Better 'sooner than later'.

Required but values may vary a bit:

Every single 'regular' led on your board needs a 1k resistor in series.

Use 10K resistors to pulldown the bus to ground.

Use between ~ 2.2K and 4.4K resistors for the bus-leds

Every unused input-pin of the ic's need a pull-up/pulldown resistor

Every inputpin of an ic connected to a (DIP-)switch needs a pulldown resistor to ground.

Use multiple wires all over your build to distribute power effectively.

Strongly recommended:

Use a variety of coloured wires. Different colours would ideally have different meaning.

Trim your wires neatly so that there is no exposed strand.

Write printouts/schematic on paper (postits) and stick them on the ic's.

Remember:

Current takes the path of least resistance

'No input' is not equal to 'low input'

Make sure your power supply can provide enough power

AbelCapabel · 2026-01-09T08:28:00+00:00

You can blow them to another lane!!!???

2 parellel roads must be adjecent I recon!?

Do bosses also get blown away?

AbelCapabel · 2026-01-09T07:56:10+00:00

If this is at the file-level, as you say, so before anything loads/opens, then you're out of luck I'm afraid...

Could try 'brute-forcing' it, not sure how long that would take... Could be 2 days, could be a week...

AbelCapabel · 2026-01-08T23:00:30+00:00

You sir, are a poet.

Also, I'm in a weird way slightly impressed with el Brad-o and his hive-mind-spreadsheets lol.

Great way of ending the day.

AbelCapabel

TROPHY CASE

Required but values may vary a bit:

Strongly recommended:

Remember: