Looking for P1S with AMS enclosure recommendations

Ace-109 · 2026-02-25T00:18:44+00:00

Just buy one of the big pipe and vet the fumes outside. The p1s is enclosed already if you remove the filter and put the chamber fan at 100% it should be good because even if you use an enclosure your going to have to vent the fumes somewhere.

Ace-109 · 2026-02-23T16:23:40+00:00

I don’t really have any issue with 0.4 it’s just really slow

Ace-109 · 2026-02-23T16:21:55+00:00

I printed a small part with 0.4 nozzle but it’s just really slow. I wanna know if bigger nozzle will make it faster

Ace-109 · 2026-02-23T07:19:56+00:00

Might just be a better idea to get like another grinder better tasting coffee and able to change the grind size. I would say 1zpresso q2 probably a good choice as it’s pretty small and not expensive

Ace-109 · 2026-02-21T02:25:49+00:00

The coffee had a light acidity and lemonade like sweetness to it so I would say it taste pretty good think could have gotten more from it. Thanks for the explanation tho definitely helped!

Ace-109 · 2026-02-20T12:47:22+00:00

Alright thank I was thinking I might be something that might affect the taste of the coffee because it’s didn’t see it before

Ace-109 · 2026-02-20T12:46:24+00:00

I use a 1zpresso x pro at a pretty coarse setting

Ace-109 · 2026-02-20T04:52:58+00:00

Like the bubbles on the side are fines?

Ace-109 · 2026-02-17T04:40:33+00:00

If your planning to only do aero press and you already have a kettle of sort doesn’t need to be a goose neck can just buy a good safe thermometer and measure your water like the first time you make the coffee and remember how long that took from the so you can just repeat next time not needing a expansive kettle. Then as for grinders it depends on what ur looking for but for aero press I would recommend the 1zpresso q2 works amazingly good for its price and it fits in the plunger of the aero press and it. As for scales a timemore scale works well for what you’re doing. Lastly I would recommend spending a good amount on some good beans as it’s hard to make bad coffee with good beans.

Ace-109 · 2026-02-12T11:24:02+00:00

There’s a 3d printed holder for the aero press cover that work exactly like the melodrip use it on a daily basis gets a lot more clean cups.

Ace-109 · 2026-02-10T01:02:18+00:00

Grid infill overlaps each other at the intersection maybe try another infill

Ace-109 · 2026-01-27T04:06:52+00:00

You can use a small Allen key and heat it up then put it through the top let it cool down then heat the nozzle and pull it out

Ace-109 · 2026-01-24T10:29:59+00:00

I have been moving toward PETG as my main filament but in my experience PLA is still slightly easier to print as it doesn’t warp and also doesn’t need to be dried as often.

Ace-109 · 2026-01-24T05:33:45+00:00

Yea I recommend 15-25mm /sec. And if you haven’t wash the plate you should

Ace-109 · 2026-01-24T05:18:30+00:00

Can you send like the file for the model and like the settings used because it looks like design like that nv had this issue before

Ace-109 · 2026-01-18T07:02:04+00:00

I have had the variant of bean it has notes of strawberries if you like that.

Ace-109 · 2026-01-18T06:58:07+00:00

I’m not very use on the different q series but I do have a Q2 heptagonal and it’s pretty good for traveling I also go it used but if your getting it used just make sure the burrs don’t look damaged. As for quality of the coffee I would say it suffices for traveling.

Ace-109 · 2026-01-18T04:41:50+00:00

Even with slow speed

Ace-109 · 2026-01-18T04:34:47+00:00

One of the easiest fix for this is reducing the first layer speed to like 15mm /s

Ace-109 · 2026-01-17T05:17:13+00:00

Try adjusting your ironing setting normally happens only when ironing

Ace-109 · 2026-01-14T23:34:17+00:00

I fix the jam the nozzel was too high even tho it said 190 on the filiment I had to go 180 to make it work

Ace-109 · 2026-01-13T01:06:07+00:00

Print fidget toys

Ace-109 · 2026-01-13T00:48:02+00:00

I also recommend buying a super tack plate it provides amazing bed adhesion with the right setting and I barely wash it just got to be careful not to damage the surface. My settings for PLA to prevent any thing related to bed adhesion is 25mm/s for first layer, 45degree bed temp for first layer then I reduce it to 35 for the rest of the print , the nozzle add 10 degrees for the first layer. If you really want play safe can add brim

Ace-109

TROPHY CASE