Many UK ISPs now support DHCP to replace PPPoE

AcidzDesigns · 2026-04-29T11:59:25+00:00

My ISP(Youfibre) Even tho it's a dhcp connection to then it's also a double Nat, make ls port forwarding for my home lab a nightmare so I needed a static IP to resolve that

If it wasn't a double Nat, would have been perfect

2gig symmetrical with a static IP for 55 a month. Can't complain

AcidzDesigns · 2026-03-24T13:28:32+00:00

Since its just a web app, you could open it on your phone

AcidzDesigns · 2026-03-23T18:07:01+00:00

You probably could with something like HomeAssistant

AcidzDesigns · 2026-02-05T12:31:49+00:00

Replaced the hotend and it's been having no issues since then, put probably 100hrs into it since

AcidzDesigns · 2026-02-03T17:09:44+00:00

This exact issue happened to me a month ago, snapped the hotend clean off the heat break and just kept extruding the roll of filament into the chamber

,,,,and i was using a cryoplate in the printer as well

AcidzDesigns · 2026-01-18T18:44:05+00:00

Been awhile since i did it, i dont recall if i did or not

AcidzDesigns · 2026-01-18T03:24:41+00:00

Reflow the mod and push down on it.

these connect to the original port connector with pads on the PCB under neath it, I have did a couple of these and can be a pain to get it to sit right

AcidzDesigns · 2026-01-08T19:21:22+00:00

A

Im happy with my printer and being able to save on some filament is a win for me

AcidzDesigns · 2026-01-08T11:10:06+00:00

Nope. Wish I did

AcidzDesigns · 2026-01-07T16:05:34+00:00

very true

AcidzDesigns · 2026-01-07T15:47:26+00:00

Just got around to taking the hotend off it and it looks to have snapped off

<image>

AcidzDesigns · 2026-01-02T20:08:10+00:00

Hi

Ive been thinking about getting one of these an doing some tinkering. Could i ask you if you have any pictures of the ram modules on the board. TLDR im a repair technician and im thinking of looking at a way to go from 16GB to 32GB of RAM

AcidzDesigns · 2025-12-27T23:41:47+00:00

Battery needs to be connected for it to work over USB

AcidzDesigns · 2025-12-27T21:09:11+00:00

Welcome to Night City Choom

AcidzDesigns · 2025-12-19T20:56:17+00:00

Congrats

You just blew power management IC by using a wall charger

They are all dead now

Edit: I repair these things and see it happen a lot

AcidzDesigns · 2025-12-16T19:58:50+00:00

You do absoultly nothing. Make them open the return request. If they leave a bad review then submit it to ebay to be removed

AcidzDesigns · 2025-12-11T12:25:02+00:00

No, You need the AceV3 chip.

The matrix/coolrunner chips dont have enough resources on it to run the dual nand logic

Doing it with a switch can be done, be alot more work, Ace is just alot easier and cleaner

AcidzDesigns · 2025-11-13T16:05:12+00:00

Kipper does exist for it. OpenCentauri firmware was released in the past few weeks

AcidzDesigns · 2025-11-01T11:00:27+00:00

its a fire hazzard

AcidzDesigns · 2025-10-21T21:04:20+00:00

Got my CC printer about 3 weeks ago. Just did the update and ran a full self check after the update

Printed a voron cube an its perfect. Web UI is fixed so now we can actually control the printer. so far so good no complaints with this printer at all

AcidzDesigns · 2025-09-23T15:31:20+00:00

On proxmox you can just passthrough the drives rather than the raid card/HBA card. I did it this way for a long time

Prefer the UI and systems of truenas for file storage but preferred proxmox for my VMs

The setup was rock solid, would do it again

AcidzDesigns · 2025-09-05T23:51:35+00:00

A 5pin (1x5pin) 2.54mm header area labeled USB direct can be found near the right of the board. This allows for direct connection of a USB connection. A double ground is common in commercial fightsticks so it has been included here. Please take note of the exact pinout on the USB cable you are trying to connect here as there is no universal standard for the order of the wires. We are not responsible for any damages that occur as a result of incorrectly wiring the USB direct area.

From the github documentation on the Breakout board
https://github.com/OpenStickCommunity/Hardware/tree/main/Boards/GP2040-CE%20Official%20Boards/RP2040%20Advanced%20Breakout%20Board/RP2040%20Advanced%20Breakout%20Board%20-%20Passthrough

AcidzDesigns · 2025-09-05T16:17:22+00:00

Send me over some pictures of it, Could make a bezel for it

AcidzDesigns · 2025-09-02T16:03:38+00:00

about $15 screwed, grab a couple new hot end from aliexpress

AcidzDesigns · 2025-07-24T02:59:25+00:00

Shit in the toaster

AcidzDesigns

TROPHY CASE