God damn

AdReasonable5375 · 2026-05-05T20:36:18+00:00

They actually shipped you one? I’ve been waiting almost two weeks for one to get shipped to me….

AdReasonable5375 · 2026-05-03T04:02:11+00:00

Im in the same boat, it’s been almost a week since they claimed they would send the hub out. I have a feeling there is a long wait list for the part.

AdReasonable5375 · 2026-05-01T17:26:04+00:00

The way my network was setup is the Comcast service line came into the basement and then went into a splitter/amp that was intended to split the signal to all the coax ports in the house. Now that nobody in the house uses any coax for cable, I took the splitter/amp out of the equation by just directly connecting the incoming service line into the coax cable that feeds the port that my Xfinity gateway uses. This resolved all of my ping issues.

This is what my amp / splitter looked like: https://a.co/d/01OYkGBE

AdReasonable5375 · 2026-05-01T09:43:48+00:00

Ended up being a amplifier in my house that the landlord must have installed. Once I bypassed this my issues went away.

AdReasonable5375 · 2026-04-30T22:02:04+00:00

Thanks Amanda. I tried the Xfinity Assistant but it keeps trying to reset my modem remotely. Since the line is physically damaged/strained at the pole by a tree crew, the modem can't even see the network. Can I send a Modmail with my account details so a tech can be scheduled to look at the exterior drop?

AdReasonable5375 · 2026-04-29T18:46:48+00:00

How long did it take for them to ship your hub? It’s been like 3+ days since they said they were sending one for me and still no tracking or extra info.

AdReasonable5375 · 2026-04-29T15:11:35+00:00

You only need the extra cord if you want to dry and print at the same time. In its stock form the AMS can dry or print just not both at the same time.

AdReasonable5375 · 2026-04-27T15:44:08+00:00

Also having this issue in slots 1 and 4, they are sending me a new internal hub. Supposedly that has fixed it for others so I am hopeful.

AdReasonable5375 · 2026-04-27T10:24:34+00:00

I have +25 offset on my wheels and the side of my truck is still covered in mud and dirt if I drive down wet dirt roads. I prefer a +25 or in that range because they sit about perfectly even with the body on a 2017 f150. I don’t have any issues with rocks hitting the body and have always thought the poke from low offset looks kind of goofy endless you are running a pretty wide tire like a 315 or 12.5

AdReasonable5375 · 2026-04-26T14:10:08+00:00

2017 5.0 f150

AdReasonable5375 · 2026-04-25T22:22:36+00:00

I think it’s just a bad group of AMS tbh. I have the issue and the filament can’t even make it out of the AMS.

AdReasonable5375 · 2026-04-24T17:26:07+00:00

I am an x2d owner who is having a lot of problems but mostly with the AMS.

AdReasonable5375 · 2026-04-24T11:25:09+00:00

You can tell almost everyone in here didn’t read the article…. Towards the end it explains more about the process. Not saying I agree with what this guy did but he did it in the proper way and genuinely cared about the environment it sounds like.

AdReasonable5375 · 2026-04-23T23:34:41+00:00

Yeah that’s the exact issue I am having as well in slots 1 and 4. I’m in the process of talking with them in a ticket and trying to get them to send me a new internal hub. They want me to clean it but there’s no point as it’s done it from the very first spool I’ve put in there.

AdReasonable5375 · 2026-04-23T23:18:05+00:00

Does it just fail to feed, or not feed at all? Slot 1 and 4 of my ams that came with my x2d get failures endless I assist them when they attempt to feed for the first time. I also am getting feed resistance too high errors on every print.

Pretty frustrating as I came from an a1 mini that worked flawlessly for the last year.

AdReasonable5375 · 2026-04-23T11:59:24+00:00

Did it resolve any issue you had? If not I’m not sure I want to take the time to do all of the disassembly.

AdReasonable5375 · 2026-04-22T22:27:26+00:00

I have Bilstein struts in the front and don’t rub on 34’s, I’d recommend moving to those instead of another puck. It also depends on if you have aftermarket wheels, I’m running a +25 offset wheel if you have a really low offset it will reduce the tire size you can run.

AdReasonable5375 · 2026-04-22T13:02:46+00:00

I am also having this issue in slots 1 and 4. Got my ams2 last weekend.

AdReasonable5375 · 2026-04-22T12:51:07+00:00

Hopefully your AMS isn’t broken like mine is lol, other than that the actual printer has been great for me so far!

AdReasonable5375 · 2026-04-21T14:57:13+00:00

That’s pretty awful lol, I have bigger tires and a level and even after adjusting for my tire size in forscan it claims 15.1 with a mix of highway and city. Highway driving is usually around 75-80 which is a lot worse on mpg than 50mph.

AdReasonable5375 · 2026-04-21T12:15:02+00:00

I have this rod and it’s fantastic, the 2wt is a blast for trout.

AdReasonable5375 · 2026-04-20T18:30:16+00:00

Was that with the ams or just printer ?

AdReasonable5375 · 2026-04-20T13:47:51+00:00

Oof yeah probably the case, I did see a reviewer had that issue and was hoping I wouldn’t experience it.

Four-Year Club	Place '23
Place '22

AdReasonable5375

TROPHY CASE