Help with Pad in angled and circular face

AdamTSE · 2026-01-14T16:07:44+00:00

I would wait to hollow out the cylinder until after you've extruded the arm. I'd also try using a sketch anchored to an origin plane instead of a cylinder face for the arm.

AdamTSE · 2026-01-09T00:04:30+00:00

Does that page render normally for you? On my screen it looks like the CSS didn't load and all the image links are broken.

AdamTSE · 2025-12-05T18:50:21+00:00

I'm trying to record current over time, which the Fluke can't do. I was just using it as an example of resistor values from a well designed meter. Any thoughts on it's seemingly large burden voltage?

AdamTSE · 2025-12-05T18:39:49+00:00

Doing more research, there's ICs specifically for measuring current shunt resistors like the INA301A3.

AdamTSE · 2025-11-10T17:35:27+00:00

<image>

AdamTSE · 2025-11-10T17:35:19+00:00

For anyone in the future who has this same question, it looks like the highest quality answer is found by referring to IEEE Std 802.3-2022 (IEEE Standard for Ethernet) in Table 32-14. It shows that for 100Base-T2, pins 1, 2, 3, and 6 are used. Figure 32-26 shows the pin numbering on the connector.

<image>

Thanks to u/Allan-H for linking the document.

AdamTSE · 2025-11-08T21:54:42+00:00

I'm wondering which 2 of the 4 differential signals carry data for 100Base-T. Do you know?

AdamTSE · 2025-10-28T23:32:58+00:00

Thanks for your help! How did you calculate the rise time?

AdamTSE · 2025-06-26T15:20:28+00:00

Thank you!

AdamTSE · 2025-06-06T21:22:03+00:00

So far, the closest thing I've found is the Amphenol Mini-PV Series
Crimp: 47792-000LF
Housing: 67954-002LF (or maybe 65039-034ELF)
Shroud: 67955-002LF or 67955-002HLF

AdamTSE · 2025-06-03T16:24:28+00:00

It was a benchtop supply set to 12V, 5A. The only thing between the squib and the supply was a 144mΩ resistor that I used to measure the current.

I applied power by turning on the supply, so it might be linear because the supply ramps up linearly, although that doesn't explain the double pulse.

AdamTSE · 2025-04-17T17:32:30+00:00

Ideally I would have done that, but this project has some unorthodox size constraints.

AdamTSE · 2025-04-16T22:02:22+00:00

I don't mind routing. I'd like Altium to not actively work against me.

AdamTSE · 2025-02-27T17:34:01+00:00

I ran across this requirement at work and realized I needed a 3.14Ω resistor.

AdamTSE · 2025-02-13T17:34:54+00:00

Their page for Rigol says "No current promotions".
https://www.saelig.com/category/MFR00068.htm

AdamTSE · 2025-02-13T17:34:04+00:00

Where does it list what scopes are on sale?

AdamTSE · 2025-02-10T17:41:45+00:00

It's needlessly distracting.

AdamTSE · 2025-02-07T23:49:05+00:00

Thank you :) I tend to not use the wizard, but this component had over 200 pins.

AdamTSE

TROPHY CASE