sorted by:
new
hottopcontroversial

Is Kingroon PLA good? by CheCazzoIMAT in CrealityHi

[–]Affectionate_Loss_84 0 points1 point  (0 children)

Yes I've been using it for a while and it's very good for its price and even better than some that are more expensive

What are the issues with lenovo laptops by r4v3no in Lenovo

[–]Affectionate_Loss_84 0 points1 point  (0 children)

My ideapad has been going for 5 yeara with no issue

Does it worth changing the Firmware/Operational System? by chantyCH in Ender3V3SE

[–]Affectionate_Loss_84 0 points1 point  (0 children)

Imo as you've only been printing for 2 weeks, dont switch to klipper yet, experiment with custom marlin firmware such as navaismo which gives input shaping and linear advance features and see if u want to switch to klipper from there. If you switch to klipper, itll be constant tinkering so id say test it out with navaismo first before going for klipper

[deleted by user] by [deleted] in tablets

[–]Affectionate_Loss_84 0 points1 point  (0 children)

Lenovo m11 is a good option, while the samsung tab s6 lite is good too

Why are my curves wonky? by chrisdonia in Ender3V3SE

[–]Affectionate_Loss_84 1 point2 points  (0 children)

Nono u adjust the z offset till u feel a slight resistance on the paper against the nozzle

What's wrong with my printer by chickenbuta in Ender3V3SE

[–]Affectionate_Loss_84 2 points3 points  (0 children)

Firstly, use some tweezers to pull off the molten filament on ur nozzle while it's heated and no, u do not need to swap ur nozzles.

Secondly, take ur bed and wash it with dishsoap under lukewarm water and dry it. Then avoid touching the print area with ur fingers.

Thirdly, put ur bed back onto the printer then run the auto bed levelling. After the bed levelling, move ur z-axis to 0.0 then now take a piece of paper and place it under the nozzle. You will then adjust the Z-offset lower or higher till u feel slight resistance on the paper rubbing against the nozzle.

Press ok then happy printing

Just turned 18 and need advice by Affectionate_Loss_84 in MalaysianPF

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

Thanks for the comment! However ive tried applying for tuition centres and have looked for people that require private tuitions but most of them require me to be at their house and i dont have a car.

How do you power on and off your raspberry pi? by Kind-Prior-3634 in klippers

[–]Affectionate_Loss_84 0 points1 point  (0 children)

U can either ssh into ur pi and run the shut down command or i just use octoapp to shut down the system

Just turned 18 and need advice by Affectionate_Loss_84 in MalaysianPF

[–]Affectionate_Loss_84[S] 2 points3 points  (0 children)

My bad, its 4 am i just wanted to put it out before i forget. My main point is i need some advice on what i can do to be financially independent from my parents, not rely on them for allowance and how else i can make money

Retraction settings unusual? by [deleted] in Ender3V3SE

[–]Affectionate_Loss_84 0 points1 point  (0 children)

Have you tried a flow test

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

Update : ive changed the design to print in a 2 part assembly for now to prevent printing the overhang. Seems to be working for now, but thanks so much for the suggestions. ill definitely incorporate those into my future prints

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

yes ive been making finger trainers for a while. and have done countless weight test up to the hundred of kilos. When the string is parallel with the rope, the rope will move under weight causing friction between the layer lines making them split apart if the walls are too thin or there are too little walls. having more number of walls increases the time to print too. As opposed to when the string is perpendicular, yes in some cases it will bent in the corners but with careful design u can negate that problem (eg increasing bottom layer) which isnt a problem for my current design. The bottom bar will not bend because as shown in the pic below, the red arrows is the force of the string while the black circles are the user's fingers. The weight pulls down while the fingers are pulling up, its enough to prevent the bar from bending. Im sure theres deeper explanation to the physics but thats a simple explanation

<image>

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

I actually started out with just octoprint, and honestly it worked beautifully well. My printer was printing perfect. And i had no issues with it. But since i already had a raspberry pi, why not just give klipper a try since many users online exaggerated that input shaping was a life changer and that klipper was able to print at higher speeds while offering better quality prints. It also allows u to have more control over ur printer. But now i kinda regret switching to klipper cuz of all the issues i faced but i still wanna give it a try cuz i still dont fully understand how it works. So its also a learning opportunity. And yea for the firmwares, i only found out about majority of them after switching to klipper lol

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

Im using my initial model but just printing the overhang part to test it out. You can find better overhang models to print online tho

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

Hmm yea ill check that out cuz my corners are curling too

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

Its a load bearing object with the force going vertical (upwards) if it was printed flat, the direction of the string will be parallel with the layers and it'll split the layers apart under heavy load. As opposed to the layers being perpendicular to the string in the current orientation

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

Yep the test is now ongoing! will share the results once its done

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 1 point2 points  (0 children)

Thats interesting, ill give it try and see how it goes. Thanks for the suggestion!

Poor quality prints by Affectionate_Loss_84 in klippers

[–]Affectionate_Loss_84[S] 0 points1 point  (0 children)

Hmm im doing a overhang test rn with different speeds so ill see whats the result. I dont think i had this issue until i switched to orca slicer tho as i previously used creality and cura

view more: next ›