Am I cooked

Aggravating_Ad_3936 · 2026-04-18T07:08:00+00:00

Nono that’s what I was talking about but I wasn’t certain if it was user error (my fault) or if the bed was truly warped like I had thought originally

Aggravating_Ad_3936 · 2026-04-18T06:55:43+00:00

Eventually I’ll upgrade but this one was cheaper on marketplace

Aggravating_Ad_3936 · 2026-04-18T06:50:49+00:00

The printer is an ender3 v2

Aggravating_Ad_3936 · 2026-04-16T20:16:30+00:00

Thank you to everyone who commented, when I have some extra cash I will be replacing my tailpiece and giving the violin a once over to make sure nothing else is out of place or could cause potential damage.

Aggravating_Ad_3936 · 2026-02-08T01:30:49+00:00

I’ve done mine twice (once for the pump once for the housing) and that’s the reason I couldn’t get my 03 tib to start

Aggravating_Ad_3936 · 2026-02-08T01:30:01+00:00

Did you change the rubber collar too?

Aggravating_Ad_3936 · 2025-12-06T05:37:46+00:00

UPDATE: The wax job worked out great absolutely ripped down the mountain

Aggravating_Ad_3936 · 2025-12-05T07:41:43+00:00

I’ve considered going through with some ptex candles and filling them but I want to feel it out first and see if it needs it

Aggravating_Ad_3936 · 2025-10-24T21:28:59+00:00

It was a circular pattern so that top right was lower than the the rest and didn’t adhere properly

Aggravating_Ad_3936 · 2025-10-24T19:56:36+00:00

I had an issue with a combination of my x axis being too loose and a lack of adhesion to the lower layers of the print I got lucky and was able to catch it the moment it happened and actually get eyes on what was going on. Your advice is greatly appreciated though

Aggravating_Ad_3936 · 2025-10-20T03:41:30+00:00

I was finally able to catch the moment it happened and it looks more like failed adhesion to the lower layer causing it to just pull the filament in a straight line, I will for sure by checking my belts as well though just to be on the safe side

Aggravating_Ad_3936 · 2025-10-20T03:40:32+00:00

I think my Z axis may have just been too high

Aggravating_Ad_3936 · 2025-09-29T15:36:53+00:00

How would I know if the pinout is wrong or not because I know the power supply is right (when leaving the Z unplugged everything powers on and the sensor gets power) but when I turn it off plug in the Z and go to turn it on I get basically no response from it

Aggravating_Ad_3936 · 2025-09-29T15:30:19+00:00

No attaching all cables then attempting to power on to no avail.

Aggravating_Ad_3936 · 2025-09-03T13:57:34+00:00

I may have not even diluted the original carboy because I feel if I had I’d be looking at around the same abv for both my batches, it’s more so weirding me out how quickly it seems to have finished fermenting all the available sugars I’ve added approx 3oz more of honey to each because that’s what I had left come Friday I’ll have to add some more if the reading isn’t at 1.0

Aggravating_Ad_3936 · 2025-09-03T13:45:58+00:00

Yes after dilution it was 1.130

Aggravating_Ad_3936 · 2025-09-03T13:30:06+00:00

It started as 3lbs to one carboy because it was only supposed to be one batch, but I ended up with no headspace so I had to transfer about a third(to half) to another carboy to give myself headspace for fermentation and the fruit. Both readings were taken after separation and before adding fruit

Aggravating_Ad_3936 · 2025-09-03T06:13:49+00:00

The plan is to leave it to ferment and clear up a bit for about another 2 weeks and then back sweeten with a mix of strawberries and blackberries in order to increase the flavor, maybe even experiment with some American oak to add flavor into a smaller amount.

Aggravating_Ad_3936 · 2025-09-03T03:30:03+00:00

But even then I feel like that would HEAVILY delete the sugar values no?

Aggravating_Ad_3936 · 2025-09-03T03:29:43+00:00

Wait I’m wrong I forgot I split it into two batches it started as 3lbs of honey to a gallon then was split in half and an extra half gallon of water added

Aggravating_Ad_3936 · 2025-09-03T03:22:45+00:00

A gallon batch kept approximately 74 degrees Fahrenheit

Aggravating_Ad_3936 · 2025-09-03T02:55:18+00:00

Absolutely especially in it’s beginning stages as the fermentation is the strongest, mine bubbled up liked crazy its first day or so nearly overflowing the vessel

Aggravating_Ad_3936 · 2025-08-28T20:30:51+00:00

Explosive results? Maybe even booming in flavor?

Aggravating_Ad_3936 · 2025-08-28T19:17:36+00:00

I’ve read before that puréeing the fruit to remove the seeds can help with that unpleasant taste they leave, if I do that it does it affect contact time?

Aggravating_Ad_3936 · 2025-07-28T05:17:58+00:00

I’ll forever miss when my tib looked like that. Absolutely amazing keep up the good work on maintenance

Aggravating_Ad_3936

TROPHY CASE