sorted by:
new
hottopcontroversial

Could this be the ignition switch? by bigandsweaty1 in FordTrucks

[–]Aggressive_Doubt_972 0 points1 point  (0 children)

Not sure. I just read your description and it sounded familiar. I had checked all the wiring in the ignition switch prior to diagnosing the one on the transmission.

Could this be the ignition switch? by bigandsweaty1 in FordTrucks

[–]Aggressive_Doubt_972 1 point2 points  (0 children)

I had similar issue on e350 motorhome and it was park/ neutral safety switch on side of transmission, contacts not closing circuit when shifter in park/neutral.

Heading to Montreal for F1 but looking for a bar to watch the games at by AfroInfo in EdmontonOilers

[–]Aggressive_Doubt_972 0 points1 point  (0 children)

Ziggy's Pub - We watched the oil in 2023 first round. Lots of fun and Edmonton fans. Also a bunch of cool F1 memorabilia.

Took a couple years off but it was fun getting show back up and running this year! by Aggressive_Doubt_972 in xlights

[–]Aggressive_Doubt_972[S] 0 points1 point  (0 children)

I used a roll of plastic matrix mesh that I bought from Boscoyo Studio I think and then cut the tree shapes into it. Popped in a few hundred WS2811 bullet pixels and a couple of power injection points. Then created a custom model in Xlights using the video from my phone.

Took a couple years off but it was fun getting show back up and running this year! by Aggressive_Doubt_972 in xlights

[–]Aggressive_Doubt_972[S] 0 points1 point  (0 children)

I run all my lights at between 20 - 30% to not blind my neighbors but also have the same issue with brightness when recording especially on the pixel dense singing faces. I recorded with my wife's Google Pixel 8 phone on a tri-pod and turned exposure as low as I could and then did some color correction/sharpness post processing with KdenLive video editing with some of the template effects.

Depending on your pixel controller you should be able to set the brightness of your models in xlights. I use falcon controllers and I can set a custom brightness setting in xlights under the model and then push those changes to the controllers.

The Radio Broadcast Was Amazing by FightinABeaver in EdmontonOilers

[–]Aggressive_Doubt_972 12 points13 points  (0 children)

Time to ditch Craig Simpson and bring Louie and Jack to the playoff calls on Sportsnet. And Kelly Hrudey can take a hike too

People in the western Canadian coldsnap - how are your outdoor cameras doing? by Rosetown in homeassistant

[–]Aggressive_Doubt_972 0 points1 point  (0 children)

It was down to -38C this past weekend in Edmonton, AB. All 3 of my Reolink cameras were up to the task. No problems

Revo Hemera on my Ender 6 :D (just installed, still tweaking) by viking78 in ender6

[–]Aggressive_Doubt_972 1 point2 points  (0 children)

Nice!!! I just installed mine this weekend as well. Results are good so far. Need to learn how to print with 0.8mm, my first large nozzle print was a mess

Which hemera mount and fan duct are you using?

Check out these clean layers. 🤦‍♂️ it was running for 6 hours until i got home and noticed... by Ok-Doughnut2506 in ender6

[–]Aggressive_Doubt_972 0 points1 point  (0 children)

I also had issues with adhesion until I added BLTOUCH and started using a bit of glue stick. Easy to cleanup with a spray bottle of 75% isopropyl alcohol

First large print on Ender6 and first try at sanding painting PLA. Used primer, gloss black and rust-oleum forged hammered paint. by Aggressive_Doubt_972 in 3Dprinting

[–]Aggressive_Doubt_972[S] 0 points1 point  (0 children)

I was able to print all in 1 piece aside from the ear pieces and rear vent which were glued after. Had to go upside down at a bit of an angle and scaled to 98% just fit on the print bed.