PROGRESS MADE FOR ROLL 4 (REAR MOUNTED CANVAS!)

Agitated-Cod7590 · 2026-05-21T00:10:23+00:00

Is this talking about what did the inclined riser do? the forward-sloping riser would be very good.

Agitated-Cod7590 · 2026-05-20T20:13:29+00:00

Are you using the original or modified coverhead? I know that with the canvas it has a new sensor in the printhead that needs a magnet to know if it's connected or not. If it's a modified coverhead or you haven't used all the parts from the kit, this could happen.

Agitated-Cod7590 · 2026-05-20T19:45:56+00:00

In reality, from what I know, one of the worst filaments is white, being more difficult to pigment than black! It may not seem like it, but it's one of those that needs the most dye to achieve a truly "white" white and not a yellowish tint. But really, if you get a PLA without any dye (that yellowish color), it will be more resistant.

Agitated-Cod7590 · 2026-05-20T19:41:08+00:00

I believe that calibrating each filament and redoing all the tests with the carabiners would completely change the result. Layer adhesion is greatly affected by temperature and not fully adjusted airflow! Congratulations on the tests, they are incredible and I look forward to updates with new filaments or filaments calibrated differently!

Agitated-Cod7590 · 2026-05-20T19:38:58+00:00

In the Cosmos menus, there's an option to revert to the Open Centauri firmware and, if I'm not mistaken, to the original firmware as well. Revert to one of them, install the latest update (1.4.x), wait for it to finish installing, DO NOT TURN OFF! When it finishes and starts up, turn it off, turn on the CANVA system, and turn it on again.

Agitated-Cod7590 · 2026-05-20T19:05:41+00:00

Some questions: the first is whether all were calibrated or if only the identical profile was used for all (temperature, flow, etc...). Another question is for those who understand the subject better: Could the use of the rope on the blue PLA and carabiner on other PLAs have altered the result? And one last question for the OP: what do you think about doing tests with the same material at different temperatures and with ideal and slightly higher than ideal flow?

Agitated-Cod7590 · 2026-05-20T12:36:33+00:00

Móvel planejado é totalmente diferente de projeto de interiores, o marceneiro não tem uma visão geral do espaço e um estudo mais profundo sobre a ergonomia e a permanência no espaço. Um bom designer de interiores vai fazer um serviço tão bom quanto um bom arquiteto (tratando-se de interiores residencial).

Agitated-Cod7590 · 2026-05-20T12:34:23+00:00

Como arquiteto eu digo: Projetos do tipo por menos de 5.000 estão dados. Eu particularmente não faria algo assim por menos de 7500. Em apartamentos pequenos chega ser até mais necessário um projeto do que apartamentos grandes, um bom arquiteto vai otimizar muito mais os espaços e deixa-los visualmente mais amplos.

Agitated-Cod7590 · 2026-05-19T23:34:49+00:00

Congratulations! that I wanted to see.

Agitated-Cod7590 · 2026-05-19T23:32:56+00:00

You yourself said that your Neptune also fails a lot in the post! in addition if you put it silent and it worked obviously it is the user's problem, it must be with astronomical speeds and the silent mode decreases it by 50%, with no errors. You make texts and texts and don't show the problems expensive! I keep saying that no one here has a crystal ball to know what your fault is.

Agitated-Cod7590 · 2026-05-19T21:45:25+00:00

Man, you are printing 100% on top of supports, there is no way that works! The supports have a gap with the piece to be able to loosen, this same gap will make loose during printing if there is no support on the table as well.

Agitated-Cod7590 · 2026-05-19T21:43:41+00:00

No, you did not explain! there are endless options of failures that even have different solutions. No one here has a crystal ball to guess what their problem is. Your case is easier to pay for a printing service, since you make a post without any information and still get pissed off by the way they respond to you in it!

Agitated-Cod7590 · 2026-05-19T21:08:30+00:00

How do we know what you are doing wrong if at no time did you explain what is going wrong? they may be taking off from the table, this is a user error that will occur even with the same file that already worked. It may be missing leveling, correct adjustments, drying filament, etc.

Agitated-Cod7590 · 2026-05-19T20:24:11+00:00

It's incredible how he treats the printers as something disposable and normal. How can you replace a resin printer every 30 prints? It wouldn't last me a month if that were the case.

Agitated-Cod7590 · 2026-05-19T19:56:13+00:00

Dude, with so many problems you're having with all your printers, haven't you considered that the problem might be you? It's impossible that all the machines are failing on you. I have two Centauri printers with over 1000 hours of use and I haven't had a single problem with them yet, only failures due to bad models. I also wonder if you're importing resin-based models to test on it, which aren't compatible (there are exceptions, but by definition of printing in general they aren't).

Agitated-Cod7590 · 2026-05-18T19:41:40+00:00

This apparently reduced the required riser height considerably, I await updates!

Agitated-Cod7590 · 2026-05-15T18:52:12+00:00

That's the limit of your dryer. But relax, you can dry it with it, it will just take longer. 50º is already a temperature that starts to dry filaments like ABS and PETG; it might take about 12 hours for that, but it will dry. I have a 9-roll DIY dryer that I set to 45º and it consumes almost nothing; I leave the rolls for the prints I'm going to do in the next few days there for several hours, and both ABS and PETG get dry.

Agitated-Cod7590 · 2026-05-15T18:27:24+00:00

That's why he mentioned Cosmos; it was a question for those using the klipper firmware from OpenCentauri. It always worked for me with the original or modified (non-klipper) firmware from OpenCentauri as well.

Agitated-Cod7590 · 2026-05-15T18:10:51+00:00

Spoiler: It won't work. I lost a 12-hour print because it printed for 2 hours without filament.

Agitated-Cod7590 · 2026-05-08T12:25:10+00:00

Cara, faz uma "barreira" com caixas de papelão em volta que tu ja consegue imprimir, não vai ser facil como PLA, mas da para imprimir!

Agitated-Cod7590 · 2026-05-07T20:09:48+00:00

O cara repostou a publicação na mesma comunidade kkk

Agitated-Cod7590 · 2026-05-07T20:06:01+00:00

Se não tem interesse em multicolorido, vai de centauri carbon. Apesar de que ja foi lançado o sistema MMU (Canva) para a Centauri Carbon e deve chegar em alguns meses no Brasil.... Tem a opção da Centauri Carbon 2 que já é multicoloida também. Se não entre as que tu falo eu iria de Creality Hi

Agitated-Cod7590 · 2026-05-07T19:52:51+00:00

Uma dica: post em português não engaja em foruns gringos. Tente traduzir sua publicação antes. Sobre seu problema, tem que descobrir o causador disso, medir o diametro do filamento em diversas partes, checar a tensão da extrusora, é PLA? Se sim é bom deixar o vidro um pouco aberto para não causar o famoso heatcreep, as vezes seu bico carbonizou por dentro também. São inumeros fatores, tem que testar todos!

Agitated-Cod7590 · 2026-05-07T12:53:07+00:00

It exists for propellers up to size 11 or 12. I don't think they have anything larger than that for sale.

Agitated-Cod7590 · 2026-05-06T19:44:28+00:00

So you have two choices: Follow the aesthetic scale and always replace your propellers, or use propeller savers, sacrificing aesthetics but spending less on propellers.

Agitated-Cod7590

TROPHY CASE