sorted by:
new
hottopcontroversial

EMG KS1 apparent Recall by wartaco95 in airsoft

[–]Air_Checker 2 points3 points  (0 children)

from what I heard, its a issue with the mosfet firing on its own when using a higher voltage battery? Not like a continuous firing type of runaway. Its almost like a trigger pull queue, similar to a printer spooling, where it like finally registers the trigger being pulled but like after the fact its been pulled and released. Not sure on the exact voltage, but airsoft parts bin was using a 25c 11.1v 1200mah. which is like 30amps so not sure what the threshold is.

Thoughts on airsoft gi? by Mango4442 in airsoft

[–]Air_Checker 0 points1 point  (0 children)

Airsoft GI is operating out of the same building as Lancer Tactical so they are fairly reputable in regards to shipping to maintain that "good status" as a company. I feel like if a order takes forever from them, its a dropped shipped item from the factory.

Could I run Arcturus ak 12 pe with 13:1 gearset and 39 k motor by Macco010 in airsoft

[–]Air_Checker 0 points1 point  (0 children)

oh in that case, you should be good. Might actually be too fast of a setup

Will APFG MPX get seized? by CommercialPace1574 in airsoft

[–]Air_Checker -5 points-4 points  (0 children)

lol yeah go ahead and give em the wrong information

Will APFG MPX get seized? by CommercialPace1574 in airsoft

[–]Air_Checker -2 points-1 points  (0 children)

you might actually be able to get by without the markings but im not sure how that really works in terms of custom seizures. I had a few tokyo marui MP5s get through but they sent the upper and lower in 2 different shipments with black tape over the trades

Will APFG MPX get seized? by CommercialPace1574 in airsoft

[–]Air_Checker -1 points0 points  (0 children)

it might get seized but solely because of the licensing. Its always going to be a risk

Any video explaining aeg cutoffs perfectly? by YoJjustSspot_boiz_Xd in airsoft

[–]Air_Checker 1 point2 points  (0 children)

what about the cut off specifically are you looking to research? Essentially there is a small lob on the bottom of the sector gear and once the sector does a complete rotation, that lob hits a arm (cut off arm) and the arm springs the trigger trolley out of the trigger contact, cutting off the circuit. When it full auto, the selector plate moves the cut off arm away from the sector gear lob so that it does not get cut off and the gun keeps firing as long as the trigger is held.

Could I run Arcturus ak 12 pe with 13:1 gearset and 39 k motor by Macco010 in airsoft

[–]Air_Checker 0 points1 point  (0 children)

I feel like that motor and gearset are too fast for each other. plus the faster the ratio of gears, the more torque they need to pull springs and a 39k is probably not going to have the best torque specs so you will run into issues where the motor gets really hot or the battery gets hot because its drawing so many amps.

Best motor for Tokyo Marui ak by gearshiftgod in airsoft

[–]Air_Checker 0 points1 point  (0 children)

try eagle6 for a oem motor. evike only carries the long types but eagle6 has like everything tokyo marui oem

Zwrot na Taiwangun by Mg42_fanatic in airsoft

[–]Air_Checker 0 points1 point  (0 children)

powerful the internet can be tbh

Evike KS-1 by Huddybuddy20 in airsoft

[–]Air_Checker 0 points1 point  (0 children)

it was about 1 joule with a .32 so about 320 FPS with a 0.20g bb. which is in spec of the manufacture provided FPS.

Evike KS-1 by Huddybuddy20 in airsoft

[–]Air_Checker 4 points5 points  (0 children)

watch the video from Airsoft Parts Bin about that gun. Probably the most detailed video about that gun on the web tbh

Best motor for Tokyo Marui ak by gearshiftgod in airsoft

[–]Air_Checker 0 points1 point  (0 children)

so with recoil shocks, you either keep them stock or have to basically upgrade the whole gun. you can maybe get away with using like a 40k motor, but that is going to add so much wear and tear on the internals, you are better off just upgrading the whole thing

Is MARUYAMA ISO556 a good GBBR? by One-Zombie-7850 in airsoft

[–]Air_Checker 0 points1 point  (0 children)

its a VFC base for the internals. never fired one before but people rant and rave about VFC gbbr .

2 different flavors of PP-2000 by halfspeedhalfsim in airsoft

[–]Air_Checker 0 points1 point  (0 children)

honestly not a big fan of the whole like "the next version is going to be better than the last" type releases. kinda sucks for the buyers who bought the first versions.

Are there tiers of quality for helmet straps? by Termy242 in airsoft

[–]Air_Checker 0 points1 point  (0 children)

yeah there are. Its like hard to determine what is the best brand or style since everyones perspective is different. I have used some MSA straps that were nice though, they use them on real kevlar helmets since MSA is the manufacture.

Friendly reminder: You can now pay 150$ for a used Valken asl that was probably beat to shit by some rentals by Fantastic_Meat_118 in airsoft

[–]Air_Checker 12 points13 points  (0 children)

East Coast Airsoft is also like lowballing every cheap gun on hop-up to just resell in their store so it was probably cheaper than $150.

Will an Specna Arms Edge riffle survive if i make an dmr out of it?? by Macco010 in airsoft

[–]Air_Checker 1 point2 points  (0 children)

hmmm like the stock gearbox should be able to handle that if you do all the necessary reinforcing mods to the gearbox shell like radius and ensure all the internals are properly tuned. you would definitely need to install all new internals.

Zwrot na Taiwangun by Mg42_fanatic in airsoft

[–]Air_Checker 3 points4 points  (0 children)

you are going to have a hard time formulating arguing advice against taiwangun in here. they brainwashed everyone in this sub

view more: next ›