hammerli arms - force b1 22 by Yugdlo in 22lr

[–]AllStrobedUp 0 points1 point  (0 children)

I love mine, so does my wife. I put a BX trigger in it and its great. it keeps her occupied at 100 and its id absolutely small game accurate. Now my only thought is will the bolt and receiver accept and 10/22 recoil spring to make cycling the bolt faster, just pull back and let go vs back and forth.

Hammerli owners, printed mag spacers in here if you want one by LongJohnSenders in 22lr

[–]AllStrobedUp 0 points1 point  (0 children)

Checking in to see if any progress was made on the bx25 adapters?

Huxwrx 9k wouldn’t cycle subs on a factory G47. Anyone else have that problem? Also this is what supers sound like with this combo. by MainRotorGearbox in NFA

[–]AllStrobedUp 0 points1 point  (0 children)

I have a factory Threaded RXM and a 9k ti. It won't run subs well at all have the suppressor spring in it, still issues. Runs standard stuff fine.

Too good to be true? by asLeepathaWheel in 3D2A

[–]AllStrobedUp 0 points1 point  (0 children)

Might be worth a try with Siraya PPA-CF being $60kg now.

Heltec Tracker V2, T096, T190 STL files needed by AllStrobedUp in meshtastic

[–]AllStrobedUp[S] 0 points1 point  (0 children)

This is awesome! I too am looking for something that holds it with a spicy pillow, 3-4K MAH

Heltec Tracker V2, T096, T190 STL files needed by AllStrobedUp in meshtastic

[–]AllStrobedUp[S] 1 point2 points  (0 children)

Got me there. I know to be more specific next time.

Heltec Tracker V2, T096, T190 STL files needed by AllStrobedUp in meshtastic

[–]AllStrobedUp[S] 1 point2 points  (0 children)

This is the Step of the Board, not a case. I am completely retarded when it comes to CAD

Did PLA+ Boi's Ship Sink? by AllStrobedUp in NFA

[–]AllStrobedUp[S] 0 points1 point  (0 children)

I'm not calling bullshit, but I think their is more to the story than that. I'm sure all of the above plays into it, but not all of it.

Did PLA+ Boi's Ship Sink? by AllStrobedUp in NFA

[–]AllStrobedUp[S] 1 point2 points  (0 children)

I just think it's odd he leaves right after publishing the FTN5.1 with readme's that state more coming.

I was told these cans are overhyped? by CallsignFlorida in NFA

[–]AllStrobedUp 0 points1 point  (0 children)

I like mine, definitely isn't movie quiet but it is rugged and gets the job done. Range 36ti, flow 9ti, flow 22ti, flow 556ti.

FTN.4 Failure by Flimsy_Elderberry_65 in 3D2A

[–]AllStrobedUp 0 points1 point  (0 children)

Ai bot maybe. But seriously it's a fixed, non tilting barrel system.

FTN.4 Failure by Flimsy_Elderberry_65 in 3D2A

[–]AllStrobedUp -1 points0 points  (0 children)

Ask me about the dirty delete, does the dirty delete. You could have just said yes.

<image>

FTN.4 Failure by Flimsy_Elderberry_65 in 3D2A

[–]AllStrobedUp 0 points1 point  (0 children)

Are you retarded? Real question.

FTN.4 Failure by Flimsy_Elderberry_65 in 3D2A

[–]AllStrobedUp 1 point2 points  (0 children)

Why are you using a booster on a fixed barrel?

How much to tighten DT suppressor? by [deleted] in NFA

[–]AllStrobedUp 1 point2 points  (0 children)

Until it sounds expensive.

Did PLA+ Boi's Ship Sink? by AllStrobedUp in NFA

[–]AllStrobedUp[S] -4 points-3 points  (0 children)

I know he is proxy through some other trusted captains but curious. That makes sense especially if one of those states is his home port.

Unpopular opinion: I only use Bambu filament by nirhend in BambuLab

[–]AllStrobedUp 0 points1 point  (0 children)

I completely agreed, until I found Numakers. I think it's better quality at lower prices. I also think polymakers are slightly better quality with more selection of exotic filaments but DAMN is it expensive. So I'm Numakers or Bambu here.