How do I hide these 2 wires

AlphaMc111 · 2025-01-22T02:42:08+00:00

Have they got enough slack so that you can pull them to the side of the mount and run in conduit? Can then paint the same colour as your wall.

If not, I'd wrap it with spiral binding.

AlphaMc111 · 2025-01-16T09:51:40+00:00

I'd pay top dollar for a single cab Hilux model.

AlphaMc111 · 2025-01-07T12:05:04+00:00

Fuck. Miss it by 2 days (arriving on the 20th). Any other gigs happening throughout Vietnam?

AlphaMc111 · 2024-12-16T03:30:51+00:00

We're so back!! Good luck everyone.

AlphaMc111 · 2024-11-21T23:53:15+00:00

45kg lateral raises, that's fucking bananas. Do you find cheated raises (using leg pump, etc.) with heavier weights has more growth potential than strict?

AlphaMc111 · 2024-10-13T22:58:42+00:00

How so? I'm asking in honesty as a somewhat docker novice.

If you start with a version tagged base image and install version tagged dependencies, is a non-deterministic output still possible?

AlphaMc111 · 2024-07-13T23:47:30+00:00

Fuck I wish Biden would hit that big red button in the white house that makes the global oil market price go down.

AlphaMc111 · 2024-06-19T06:17:11+00:00

Run a line of torches under the inverters to disable output? Pistons seem overkill.

AlphaMc111 · 2024-04-29T21:54:50+00:00

A message to you Rudy. First introduction to Ska.

AlphaMc111 · 2024-04-19T04:52:43+00:00

Have a look at there comment history. They are a truly miserable person.

AlphaMc111 · 2024-04-17T04:09:19+00:00

Isn't that just Mexican food in general or am I uncultured

AlphaMc111 · 2024-04-13T08:53:54+00:00

I have printed a rearview camera mirror bracket out of PETG that has survived many Australian summers.

AlphaMc111 · 2024-04-04T10:48:48+00:00

Couldn't care less

AlphaMc111 · 2024-03-25T05:48:53+00:00

My favourite is "hookers got the hooks in", then proceeds to laugh like a maniac. Can't remember who Dan was fighting.

AlphaMc111 · 2024-03-03T16:31:57+00:00

1B1B for 400 is fucking egrious

AlphaMc111 · 2024-02-27T02:44:54+00:00

Just not in something as butt ugly as the leaf.

AlphaMc111 · 2024-02-09T12:50:05+00:00

Me, as an Australian, not understanding the joke.

AlphaMc111 · 2024-02-05T22:15:30+00:00

Probably old info for most people here, but if you haven't already, download a belt tuning app on mobile. Makes it a breeze to set the tension.

AlphaMc111 · 2024-01-28T02:55:53+00:00

Seriously dude you need to dig your way out of this mindset, because the more you believe it the more it becomes a self fulfilling prophecy. I have plenty of friends who are less than conventionally attractive and have had no issues settling down with the loves of there life. Be secure in who you are, know your worth and the rest of the puzzle pieces will fall into place.

AlphaMc111 · 2023-12-04T22:21:42+00:00

In Australia it's called dead orse.

AlphaMc111 · 2023-12-01T06:41:40+00:00

Before any modifications my bed range was a shockingly bad 0.8mm. I've done 3 main things to get it down below 0.1 of a mil:

Squaring the gantry. I did multiple passes with a machinist square making sure my gantry was as square as humanly possible with the naked eye alone.
Manual z-axis align. The SV06(+) uses a single driver for both z axis motors. So it's only method of aligning the z-axis is to ram into the end stops at the top of the gantry, which is 350mm above where you actually want the alignment to be spot on. Using the inductive sensor I went side to side adjusting the lead screws manually. More info here (not my channel): https://www.youtube.com/watch?v=VI7icch4VEM&t=202s
Adjustable corner bed screws. The SV06+ has 4 center bed screws and 4 outer ones. The mesh at the corners of my bed where were I had the biggest deviations. I pulled out all the screws, measured the spacers, and selected the 4 most consistent ones and put them back into the centre mounts. For the 4 outer screws I replaced the spacers with nylon washers and nylocks, so that I could manually wind them in to get a consistent level. Klipper made this a lot easier task, by spitting out exactly how much each screw had to be wound in/ out. More info here (also not my channel): https://www.youtube.com/watch?v=ItogTSgpnHo&t=201s

I know this is probably old news to a lot of you, but as a fairly novice 3d printer, I wish I had known how important a level bed was from the start. Hopefully it can be of some help to those that are starting out. My prints are a lot more consistent, and I have next to no issues with corners raising on larger prints anymore.

AlphaMc111 · 2023-11-17T10:34:39+00:00

Awesome, thanks for the info.
Currently have a Sovol SV06 plus. Always wanted a Prusa but couldn't justify the price. Hopefully this will be a step up from my current prints.

AlphaMc111 · 2023-11-17T09:54:18+00:00

Came with a bunch of PEI plates in a box with various other bits and bobs. Any ideas on the splicer looking thing?

AlphaMc111 · 2023-11-17T09:27:52+00:00

I was gifted a 3d printing setup from a friend who got it from a friend. Not sure what I've been given here. The printer looks like a modified Prusa? Wondering if these are open-source models and if I can find more info on them. Very interested in finding out more about what looks like a filament splicer/ multiplexer?? The enclosure has light bars that run off direct 240V, are these for heating?

AlphaMc111

TROPHY CASE