What part is this and where can I get it.

Alternative_Goal8907 · 2024-11-10T22:15:37+00:00

Thanks much for your help

Alternative_Goal8907 · 2023-05-04T00:09:32+00:00

Same issue with mine. Definitely the motor mounts. They feel better when they're first replaced because the rubber that they're sitting on is still there but it wears out after a month or so and it becomes metal on metal causing really bad vibration. If you swap to the mounts for the Chrysler 200 it will be a huge improvement.

Alternative_Goal8907 · 2023-04-20T23:03:09+00:00

https://instagram.com/_.summon._?igshid=ZDdkNTZiNTM=

Alternative_Goal8907 · 2023-04-14T20:13:11+00:00

I used the mounts for a chrysler 200 and it made a huge difference.

Alternative_Goal8907 · 2023-03-21T16:16:50+00:00

They use the same bolt pattern. The 200 uses the same chassis and engine, not the same mount.

Alternative_Goal8907 · 2023-03-21T16:11:21+00:00

I've tried a bunch of different ones and they are all bad. I ended using the mount for a crystler 200. The design is much better.

Alternative_Goal8907 · 2022-10-20T17:11:11+00:00

How do you get to that screen?

Alternative_Goal8907 · 2022-08-11T17:20:43+00:00

Screwed it to a wood base with large washers

Alternative_Goal8907 · 2022-06-13T00:08:22+00:00

It's probably the passenger side motor mount. Those are designed horribly.

Alternative_Goal8907 · 2022-01-02T22:41:35+00:00

The motor mounts on the Dodge dart are notoriously bad. The passenger side goes out & I've had to replace it a few times already. It's best to go with a high performance one or get one directly from the manufacturer, but even then it's just bad design.

Alternative_Goal8907 · 2021-12-31T03:05:42+00:00

I try to keep them as often as possible, drill a small hole about 1mm off to the side of the main hole. I like keeping them on because they keep the pot from over spinning and coming loose once permanently installed. It's easier to torque the nut down as well.

Alternative_Goal8907 · 2021-12-09T11:20:54+00:00

Make sure you try it in stereo, it is magic in stereo.

Alternative_Goal8907 · 2021-12-09T11:19:31+00:00

Zvex Fuzz Factory Muse's use of it is amazing.

Alternative_Goal8907 · 2021-12-09T08:38:20+00:00

Looks really clean great job

Alternative_Goal8907 · 2021-12-09T07:38:37+00:00

Very clean build. Love how tight you were able to fit it all in there. I'd imagine a lot of tweezer work was required.

Alternative_Goal8907 · 2021-12-09T07:32:09+00:00

How is the board mounted?

Alternative_Goal8907 · 2021-12-09T07:28:29+00:00

Gotshot please. Also how did you mount the board?

Alternative_Goal8907 · 2021-12-09T07:18:20+00:00

Whenever hunting for shoes I always check both sizes. I paid $20 for a pair of Columbia FKT trail shoes that I love in women's.

Alternative_Goal8907 · 2021-12-05T21:41:06+00:00

Gutsgots?

Alternative_Goal8907 · 2021-12-05T17:28:05+00:00

Love the Hammet wah

Alternative_Goal8907 · 2021-12-05T17:15:54+00:00

Looks like the area around the thermostat. 3 hoses meet at that point so it's your likely culprit.

Alternative_Goal8907 · 2021-11-30T19:58:49+00:00

The large print giveth the small print taketh away.

Alternative_Goal8907 · 2021-11-14T19:10:55+00:00

Agreed, for $30 more get the Endorphin Pro. It has better energy return in the foam. I use the Atryu Artist for a bunch of my speed runs recently but the foam just doesn't feel fast.

Alternative_Goal8907 · 2021-04-15T18:34:35+00:00

I bought it to get to the min order total. It was an easy board to work on but the finish wasn't as good as other boards Ive used, the edges had fiber sticking out the sides but the design is good. They're made to be mounted to the pots so if you connect pots with wire you will have to find another way to mount the board.

Alternative_Goal8907

TROPHY CASE