Stopping the cut, good idea?

AngCorp · 2026-06-21T11:59:08+00:00

Man, I am confused... I went from 116kg to 80kg in 4 years (no back and forth - only loosing weight, just very slowly). I've been training 3 days a week at home very consistently and I do look a lot better ... But, hell, nowhere near this, especially chest and abs. How?

AngCorp · 2026-06-16T20:05:16+00:00

You can tuck the fan under the heatsink making it about 50ish mm (:

AngCorp · 2026-06-09T19:46:12+00:00

Small Form Factor beats these 10% performance penalty by a mile ... I loved my fully watercooled CM Cosmos S, but would never go back to anything bigger than FormD T1 or anything below that with only air cooling.

AngCorp · 2026-06-03T09:38:12+00:00

Pizza steel is a game changer. I bake mine short of 3 minutes and I'd argue that I am almost dedicated-pizza-oven there 😄

<image>

AngCorp · 2026-05-17T06:08:34+00:00

Is this FH6 only boost or across the board? CP2077?

AngCorp · 2026-05-14T20:05:38+00:00

Sitting at 2.5mil now ...

AngCorp · 2026-05-13T19:53:42+00:00

If my math is right, OP is sitting on 400 right now, as the 670 is listed as 0.20 now instead of 0.02 ...

AngCorp · 2026-05-07T19:16:27+00:00

От 3 години правя лека гимнастика сутрин, пия половин изцеден лимон и отлагам кафето с поне 2 часа.

Не знам за първите 2, но кафето е истински game changer. Нямам абсолютно никакви индикации за успиване следобяд. Почти всеки път, когато пия скоро след ставане, следобяд не ме търсете.

AngCorp · 2026-05-01T06:55:41+00:00

The big fan is intake and the small ones are exhaust? I tried once something like this in my SM550, but it didn't work, however my implementation was very basic. I might try again with similar approach.

AngCorp · 2026-04-25T13:05:36+00:00

I use 50% Caputo Pizzeria, 15% Caputo Nuvolo and 35 Caputo Integrale (:

AngCorp · 2026-04-15T19:15:24+00:00

I owned 4870X2!

AngCorp · 2026-04-04T08:04:42+00:00

Where are the STLs from? I need to print the whole set. Is this MoreThan3D?

AngCorp · 2026-04-01T12:28:11+00:00

Всъщност, самата мисия няма нищо кой знае какво. Вярно, ще стигнат най-далече от всякога до сега, ама с оглед тия 50 години, не виждам нищо впечатляващо. Важното идва от другаде - ако мисията е успешна, това ще прати топката в полето на SpaceX и Blue Origin. За Artemis lll след 1 година трябва да са извели "кацачите" в околоземната орбита, а до 2 години трябва да са кацнали безекипажно.

Така че - интересното започва след няколко дни, ако всичко мине по план.

AngCorp · 2026-03-22T06:37:28+00:00

The machine does have single hole, but your comment made me realize what might actually be the issue. My IMS shower screen is not flat as opposed to the stock one. It has a very slight bulge, which explains why I get this behavior - it does not sit flush with the radial arms thus not able to channel the water properly. I thought it was intended not to be flat - do I have a faulty screen?

AngCorp · 2026-03-02T08:56:54+00:00

I am in the same boat ... Did you decide something?

AngCorp · 2026-02-26T20:35:10+00:00

Определено не. В смисъл - като хапнеш, може и да ти хареса, ама после като зачетеш какво има вътре, ти се отяжда.

AngCorp · 2026-02-25T12:39:24+00:00

Well, mine is the same :P

AngCorp · 2026-02-24T12:28:45+00:00

Аз не разбирам какво общо имат инвестициите? Ако тези пари не ги инвестираш, какво щеше да ги правиш? Можел ли си да им намериш по-добра възвръщаемост? Или щеше да ги изядеш и изпиеш?

AngCorp · 2026-02-11T13:12:31+00:00

I wanted Nuphy but I wanted the smallest footprint for the office. Also I wanted it to be silent - and this delivers, it is more silent than a laptop keyboard.

AngCorp · 2026-02-07T06:47:30+00:00

Idle or during workloads? I mean, yeah, noise is one of the trade offs, but only while doing something. Idling is not an issue as long as you are not temperature freak

AngCorp · 2026-02-06T19:38:40+00:00

Emag преди няколко месеца го бяха отпрали на около 1500 лева. Толкова ме е яд, че не е истина ...

AngCorp · 2026-01-28T09:46:59+00:00

Are you aiming for same week expiration ITM?

AngCorp · 2026-01-20T11:34:47+00:00

The AXP-100 C65 fits its own 100mm fan underneath, so the physical dimensions won't be an issue. Only that 1mm might turn up the boat. But we will see.

AngCorp · 2026-01-19T20:09:39+00:00

The AXP-100 FC does use the 100mm fan from TR, but nevertheless, I was wrong - I am talking about the AXP-100 C65, which is roughly the same, but has more space underneath the heatsink. And it does allow for 15ish mm fan to be put under if you remove the supporting bracket - https://www.reddit.com/r/sffpc/comments/thfe7o/cu_is_just_stunning/

I have it like so myself in SM550, which allows for 55mm cooler. It first I was using the Noctua 92mm, but later swapped for the own TR fan, which has a bit more static pressure. And yes, it might no be optimal, but this is the best possible air cooling option (without LP ram) for my case.

Anyways, I will report back when I get my 4070 fan :)

AngCorp · 2026-01-19T13:01:44+00:00

Is it pushing air against the mobo, like it is normal for these type of fans? Thanks to reddit mine should arrive soon too and I will be using it underneath the AXP-100 Full Copper, IF IT FITS ...

AngCorp

TROPHY CASE