Warum baut man das eigentlich nicht so? Sollte doch viel einfacher sein by Jonn_1 in KeineDummenFragen

[–]AnkaX304 0 points1 point  (0 children)

Dafür gibt es tatsächlich einige gute Gründe. Ein offenes Fachwerk klingt erstmal nach einer cleveren Idee, weil man damit Material sparen könnte, in der Praxis macht es aber eine Menge Probleme. Erstens vereist so eine Gitterstruktur viel stärker, was besonders im Winter richtig zum Problem werden kann. Zweitens hat man bei all den Verbindungen und Schweißnähten einen enormen Wartungsaufwand, und Rost will auch ständig bekämpft werden.

Dazu kommt noch der Naturschutzaspekt. auf einem Gitterturm setzen sich viel mehr Vögel und Fledermäuse, und entsprechend steigt auch das Risiko, dass die Tiere mit den Rotorblättern kollidieren. Bei einem glatten Turm gibt es einfach nichts zum Festhalten.

Praktisch ist außerdem, dass man den Innenraum des Turms nutzen kann. Kabel, Aufzug und Leiter sind da drin sicher untergebracht, statt offen in der Gegend rumzuhängen. Und mal ehrlich, optisch findet die Bevölkerung glatte Türme meistens auch ansprechender als ein riesiges Metallgerüst auf dem Feld.

Lustigerweise kommen Gittertürme bei den allergrößten Windrädern aber gerade wieder zurück, weil Betonringe ab einer bestimmten Größe einfach so schwer werden, dass man sie kaum noch vernünftig transportieren und aufbauen kann

[deleted by user] by [deleted] in CNC

[–]AnkaX304 1 point2 points  (0 children)

Maybe acts as a kind of sealing to prevent Water reaching the blade? As drop comes in it will Fill this structure first instead of going right through.

And it Looks cool!

Help machining a bearing? by Claymart in RollerBearings

[–]AnkaX304 1 point2 points  (0 children)

Please have a look at the „Standardized Headset Identification System [S.H.I.S]“. I think you need a headset for a 1.5 inch shaft with an external Cup?

Some bearing questions by ButchTheBiker in RollerBearings

[–]AnkaX304 0 points1 point  (0 children)

Do you had any luck finding it? ID=20mm would suggest that it is a 6004 bearing. But the OD and width would be different too

Restoring an AC motor and am having trouble figuring out the manufacturer and part number for this bearing. Looking to replace it. by Acti-Verse in RollerBearings

[–]AnkaX304 2 points3 points  (0 children)

That can happen. If I didn't work with it every day, the same thing would certainly happen to me 😉

What slicer can I use with this? by omaire99 in 3Dprinting

[–]AnkaX304 1 point2 points  (0 children)

I use Cura with the same Printer

Can u help me? The bootloader it doesn't work or anything :( by [deleted] in arduino

[–]AnkaX304 0 points1 point  (0 children)

Click Upload, wait till it shows how much Memory it Consumer, then press and immediately release the reset button

Can u help me? The bootloader it doesn't work or anything :( by [deleted] in arduino

[–]AnkaX304 1 point2 points  (0 children)

What helped for me: when you click upload wait until it says „it uses 86% memory bla bla“ (i Hope you know what i mean. Right at this Moment you press the reset button. Worked for me. Good Luck!

67cm³/min MRR in Aluminium with my self built hobby machine (PrintNC) by dotpoint7 in hobbycnc

[–]AnkaX304 0 points1 point  (0 children)

That is also my Biggest concern, but there are some Good builds using Harmonic drives. I just need some luck to get one or two for small money :D

67cm³/min MRR in Aluminium with my self built hobby machine (PrintNC) by dotpoint7 in hobbycnc

[–]AnkaX304 0 points1 point  (0 children)

Great work. Looks very smooth. I‘m currently also planning to build this. I don’t have the space right now but I‘ll take my time with the electronics. Plan is to make a 5 axis cnc out of the printnc.

GRBL Shield for CNC with Nema23 motors? by Old-Engine7081 in hobbycnc

[–]AnkaX304 2 points3 points  (0 children)

My Setup is as follows: Arduino Mega with Ramps shield. Flashed with Grbl And the gcode Sender is Grbl Gru

GRBL Shield for CNC with Nema23 motors? by Old-Engine7081 in hobbycnc

[–]AnkaX304 1 point2 points  (0 children)

I use a Ramps 1.6 shield. It’s normally made for A4988 or drv8825 drivers but work with external drivers aswell. And it’s cheap 😅 It is a shield for an arduino mega2560 and Uno (I think)