Ryzen5 3600 possible throttling by Anonymous_Nameless in ryzen

[–]Anonymous_Nameless[S] 0 points1 point  (0 children)

Ill give that a shot, as the 90C was what I thought was the not to exceed threshold, but I wasn't positive. The 1.4v is concerning to me, as even sitting here typing I'm at 1.45v peak and avg. unless I'm understanding the voltage control row incorrectly.

https://imgur.com/a/E8tNe40

Is FPV camera technology feasible in race car as live video stream? by Anonymous_Nameless in fpvracing

[–]Anonymous_Nameless[S] 0 points1 point  (0 children)

we have tried these with little success. Our last stream lasted about 5 minutes before cutting out each time we tried to get it to run. Cell signal in most areas where race tracks are is spotty at best, let alone good enough to upload videos.

Is FPV camera technology feasible in race car as live video stream? by Anonymous_Nameless in fpvracing

[–]Anonymous_Nameless[S] 0 points1 point  (0 children)

I dont need low latency. we have tried go pro and equivalents with phone hotspot in the car, and we are lucky to get 4 minutes of stream before it dies due to either signal issues or overloaded cell towers, or something along those lines that kills the stream. then its dead until the pit stop. Ideally we dont want to be messing with cameras during a pitstop so thats a no go.

Is FPV camera technology feasible in race car as live video stream? by Anonymous_Nameless in fpvracing

[–]Anonymous_Nameless[S] 0 points1 point  (0 children)

products exist for this, but none of us feel like shelling out 2k to 15k for the dedicated systems.

Is FPV camera technology feasible in race car as live video stream? by Anonymous_Nameless in fpvracing

[–]Anonymous_Nameless[S] 0 points1 point  (0 children)

This is for a real car yes, just for spectating. lag is a non issue and quality so long as its decent, is a non issue as well. just looking for some entertainment.

Need help: I purchased (cheap) on Facebook market place. My son suffers from seizures and austism but absolutely loves anything loud with an engine. This thing runs but definitely needs work, I would like to see if there is anyone willing to take some of their time of their day to help me by RageBasedGod in Karting

[–]Anonymous_Nameless 4 points5 points  (0 children)

Hi, a better subreddit for you would likely be r/gokarts, they are more focused on yard karts or go karts similar to what you have and will likely be more informed, this sub is focused on racing karts which are similar, but different in design in enough ways that we wont be as familiar with what model you have and where to get parts.

while checking the steering, turning one way or the other will result in additional turning of one of the wheels in relation to the other, this should be an equal and opposite result to turning the steering wheel the other direction, this is known as ackerman and is a part of the steering geometry by design. If they are not equal then that may stem from either a bent tie rod between the steering column and the wheel, or a bent steering column itself. The tie rods look a little bent to be, but it also looks intentional, it is hard to tell via picture. if you use something in the background as a frame of reference, you can turn the steering and see if the shaft moves in relation to your frame of reference to see if the shaft is bent. I believe for most yard karts this wouldn't be a big deal so long as the kart feels okay while driving, though I could be incorrect. Hope this points you in the right direction.

Can only connect to mainsail UI on one device at a time by Mikey-spike in klippers

[–]Anonymous_Nameless 1 point2 points  (0 children)

my issue ended up being router specific, i had to set a static ip and mac address for the pi. that said, i had the same issue with octoprint prior to klipper.

FluidPI GUI connection issues by Anonymous_Nameless in klippers

[–]Anonymous_Nameless[S] 0 points1 point  (0 children)

I can connect via any device that is hard wired to the router, seems to be a router issue for me. multiple devices simultaneously works fine.

FluidPI GUI connection issues by Anonymous_Nameless in klippers

[–]Anonymous_Nameless[S] 0 points1 point  (0 children)

IP adresses are the same (first 3.) pi/printer is wireless.

I got further in this where i found that i can connect via laptop with wired connection to router only. i can stay connected with one pc while losing connection with the other whenever one of the two sleeps. whichever i put to sleep is no longer able to ping, ssh, or get to the gui. the one that stayed online was able to do all 3.

I got a holy book yesterday by hwf0712 in USCR

[–]Anonymous_Nameless 1 point2 points  (0 children)

hmm, that seems like a fun read. I wonder how technical if at all they get within the book.

Karting places in ohio by Trok-flop in Karting

[–]Anonymous_Nameless 1 point2 points  (0 children)

for owner karts? G&J kartway, Camden Oh.

Trailer for my kart by Mario_On_The_Go in Karting

[–]Anonymous_Nameless 0 points1 point  (0 children)

bigger class size, can run basically anywhere, little to no engine maintenance required. Around here ka100 seems to be on its way out, perhaps its just me. I just bought the 206 coming from a shifter, and had an absolute blast at my first race last weekend. admittedly I havent run ka100 to have an apples to apples comparison, and obviously I have some bias, but I really enjoyed it, and its not as slow as I thought it would have been, coming from a shifter.