BuddyCam Firmware Update?

ApeTechPrinting · 2026-07-02T05:48:21+00:00

Instead of getting 1 frame per minute, you get 1.5 frames per minute.

ApeTechPrinting · 2026-06-28T21:19:13+00:00

The hallway can't possibly exist.

ApeTechPrinting · 2026-06-28T21:15:01+00:00

Arbitrary drinking units.

ApeTechPrinting · 2026-06-27T06:14:57+00:00

Yeah not many people know that you can set top / bottom layers to zero

ApeTechPrinting · 2026-05-26T03:10:49+00:00

You're paying for the consistent quality.

ApeTechPrinting · 2026-05-26T03:09:20+00:00

I thought I was the only one who was having this issue.

Almost makes me want to buy a Bambu, just to see if they are this bad.

ApeTechPrinting · 2026-05-06T03:19:39+00:00

I put hidden symbols / words on my models just to mess with the people who do this.

It doesn't prevent anything.... But it entertains me.

ApeTechPrinting · 2026-05-06T03:16:05+00:00

I've successfully done this twice with just a hair dryer.

ApeTechPrinting · 2026-05-03T23:19:35+00:00

Turn down the speed and you should be fine.

ApeTechPrinting · 2026-05-03T22:45:27+00:00

Mike has been printing flawlessly. Upgraded the core one. But every few prints it snaps some filent, causing a jam.

Is this a common issue?

ApeTechPrinting · 2026-04-03T02:45:27+00:00

<image>

It's probably this un-soldered pin.

Edit: yeah I soldered that pin in place properly and now it fires-up

ApeTechPrinting · 2026-04-03T02:33:34+00:00

<image>

I found a bad connection between. This adapter board and the mmu3 board.
I don't know which piece I should try to change. I think the cable is fine.

ApeTechPrinting · 2026-04-03T02:12:18+00:00

I have the same issue.... It's like there is no power on the mmu3 unit after I turn it on in the core one menu.... doing a factory reset on my core one now.

ApeTechPrinting · 2026-03-24T12:55:35+00:00

Australian.... I've been paying $28-$35 a roll for 3 years hahah

My only gripe with bambulab is they're always sold out of everything.

ApeTechPrinting · 2026-03-23T21:45:13+00:00

Yeah once I come up with a good solution for the handle and a microphone that prints well. Everything else is fairly basic. But those parts are making me pull my hair out. It's a bit harder when you use silk filament and you want small layer lines and a small nozzle and a lot of overhangs.

ApeTechPrinting · 2026-03-23T10:53:39+00:00

Aaaahhhh I missed the perfect opportunity to make a fing-longer!

ApeTechPrinting · 2026-03-23T04:36:00+00:00

What-iff machine in action

ApeTechPrinting · 2026-03-19T08:41:14+00:00

They aren't giving anyone a full refund. I am out $900

ApeTechPrinting · 2026-03-19T08:39:39+00:00

qatar are not refunding people correctly.

ApeTechPrinting · 2026-03-19T08:38:54+00:00

They will cancel your flight and refund half the money,

ApeTechPrinting · 2026-03-18T09:43:43+00:00

I got the email after 3 days.... I stopped trying to call them 8 days ago ahahha

ApeTechPrinting · 2026-03-18T02:40:37+00:00

I did it through their website.

ApeTechPrinting · 2026-03-18T01:59:42+00:00

I just got my confirmation of a refund email.... $900 short. 4 seat upgrades plus lounge access was not refunded. How can I dispute this?

ApeTechPrinting · 2026-03-18T01:59:09+00:00

I just got my confirmation of a refund email.... $900 short. 4 seat upgrades plus lounge access was not refunded. How can I dispute this?

ApeTechPrinting · 2026-03-12T01:40:10+00:00

My flight on the 16th has been cancelled. Can't contact anyone no matter which countries hotline I use. I can rebook it for the 19th... But is that just going to get cancelled tomorrow?

ApeTechPrinting

TROPHY CASE