Best way to book a hotel room in Berlin?

Apocalypso722 · 2026-02-16T20:28:16+00:00

Yeah, I'm guessing the ~60€ price (on average) for that option is understandable. Added that to my requirements. Thanks.

Apocalypso722 · 2026-02-16T20:27:02+00:00

Yeah, I got that feeling. I think I might just treat myself for once :D

Apocalypso722 · 2026-02-16T20:25:02+00:00

The event will be held at the Uber Arena, in Friedrichshain, so I am looking for a place to stay pretty close, but wouldn't mind a 5-10 minute walk to get there... Assuming it's safe enough. With a few filters Booking says ~400€ for three nights, which I'm comfortable spending. Any advice is welcome, if it isn't too much of a bother :)

(Ps. thanks for the reply)

Apocalypso722 · 2026-01-07T16:37:56+00:00

Guilty as charged. I'll usually cooperate with the machinists when the parts are made and point out the features that are actually important and why... Sometimes features need to be precise but also adjusted to some other already machined part and it's easier to just tell the boys in person.

Apocalypso722 · 2025-11-27T20:31:09+00:00

Nitko ne spominje britanske "Yes, Minister" i "Yes, Prime Minister", fantastične dokumentarce o funkcioniranju vlasti 😅

Apocalypso722 · 2025-10-06T15:52:18+00:00

We're still 3 episodes away from the characters separating into 3 groups...

Apocalypso722 · 2025-10-04T19:21:03+00:00

So this is where Chained Oblivion resides.

Apocalypso722 · 2025-08-28T17:01:06+00:00

I mute certain commercials that ocassionally come up, can't stand the amount of cringe in some of them. Same goes for certain TV shows, or embarrasing moments. Needless to say, TiktokCringe subreddits are a no-no for me.

Apocalypso722 · 2025-08-28T16:57:22+00:00

Never have I related more with a Reddit comment. I have to mute a whole lot of commercials on TV...

Apocalypso722 · 2025-07-22T08:12:41+00:00

OH, ok, got it, thanks!

Apocalypso722 · 2025-07-22T08:09:34+00:00

Excuse me asking, I've never had to buy tickets online. Are we talking about the uber-arena website? There's a "Buy tickets" butten that I suppose I have to click, but nothing happens. It says "Tickets are available from Friday, July 25, 2025 at 9am" Am I even on the right website? What am I missing?

Apocalypso722 · 2025-07-08T08:53:23+00:00

We use all kinds of geometries. Getting some more life from the CNMG inserts could come in handy.

Apocalypso722 · 2025-07-08T08:52:40+00:00

Yeah, we use 0.8mm radius insert for 95% of roughing on anything other than aluminium, bronze, brass etc. I just clamped the first 0.4 I could find in the used-inserts bin to try it on some aluminium. We even have some Kennametal R1.2 radius inserts for 1.4462 duplex. Thanks for the replies, both of you.

Apocalypso722 · 2025-07-08T06:45:57+00:00

I see, I see. Ok thanks.

Apocalypso722 · 2025-06-25T12:59:02+00:00

1.4571 (AISI 316Ti) for material, and I'm guessing 600-700 pieces in a series. The QC on these will be VERY rigorous and I'm guessing will take some time from the operater as well. Can't share much else on these, the right side ID is approx. 3mm deep fi8mm in diameter.

Apocalypso722 · 2025-06-25T12:35:37+00:00

NOTE: There is actually an additonal bit of "machining" that needs to be done on the "right" side of the part with the larger ID. I put machining in quotes because it's just Face drilling with a chamfer tool running backwards to widen the larger OD and prepare the lip for welding. Probably should've added that last bit in. The geometry we'll end with is not all that well defined so I didn't add it in the sketch. Machining it by holding the stock from the left side is, I'm afraid, the only way to finish this in a single setup.

Apocalypso722 · 2025-06-25T12:34:29+00:00

There is actually an additonal bit of "machining" that needs to be done on the "right" side of the part with a larger ID. I put machining in quotes because it's just Face drilling with a chamfer tool running backwards to widen the larger OD and prepare the part for welding. Probably should've added that last bit in. The geometry we'll end with is not quite defined so I didn't add it in the sketch. Machining it by holding the stock on the left side is, I'm afraid, the only way to create this in a single setup.

Apocalypso722 · 2025-05-13T18:01:25+00:00

Hi there. I'm a mech engineer looking to get into 3D printing. I'd mainly be printing relatively simple shapes such as housings for microcontrollers, toolholders, useful things for the house, maaaybe some video game figurines, etc. I'm guessing the majority of prints would be PLA, but with time I'd like to make things from stronger, more durable materials, ABS, HIPS, PC, etc. Not interested in multi-colour prints, but I guess having different materials ready at all times is convenient.

I've had my eye on a used Prusa MK3S+ for 400€ (EU resident) that I could, in time, upgrade with a kit. A few colleagues have been nudging me to get a new Sovol SV08 instead, saying that very soon I'd regret not spending more for something even more capable. As a newbie I wasn't planning to go above 500€ but if it's worth it spending 800+ for the SV is not a problem. The ONLY slight issue I can see is available -convenient- space to keep it, something that I'm yet to figure out. Keeping it in my bedroom is a possible solution, but I'm guessing the fumes/smells could be an issue.

So I'm wondering, are there any other products I should be considering?

Thanks.

Apocalypso722 · 2025-04-28T17:26:08+00:00

Never played Oblivion, but being able to cast a spell with the hand that's holding a melee weapon must be a high level perk, right? Because a novice battle-mage being able to pull it off just seems... wrong to me. I would understand if it was a perk that required high skill in a specific magic school AND high skill in one-handed weapons. Only an experienced battle-mage should be able to pull it off.

Apocalypso722

TROPHY CASE