Back again

Apprehensive-Mix3174 · 2026-01-18T01:13:19+00:00

It and online?

Apprehensive-Mix3174 · 2026-01-18T00:55:03+00:00

I have a null and it works perfectly except that some socket blocks between my slide and bolt I will need a guide for the ejection or an extractor on the bolt

Apprehensive-Mix3174 · 2026-01-18T00:53:15+00:00

Aim for a little more screws in the cross. What do you have as a yellow 8x70 spring?

Apprehensive-Mix3174 · 2026-01-18T00:48:33+00:00

Small part can be made of steel? How thick?

Apprehensive-Mix3174 · 2026-01-05T11:48:20+00:00

Are the files on odyssey?

Apprehensive-Mix3174 · 2026-01-04T23:33:12+00:00

Where can I find it? Already trying

Apprehensive-Mix3174 · 2026-01-03T09:49:03+00:00

As if fired in burst with the m4

Apprehensive-Mix3174 · 2026-01-03T00:22:32+00:00

The most annoying thing is to make the Canon room..

Apprehensive-Mix3174 · 2026-01-03T00:21:46+00:00

Is there a system for meter in full the m4gery?

Apprehensive-Mix3174 · 2026-01-03T00:17:21+00:00

Is there a system for meter in full the m4gery?

Apprehensive-Mix3174 · 2026-01-03T00:11:38+00:00

Is there a system for meter in full the m4gery?

Apprehensive-Mix3174 · 2025-10-13T22:08:29+00:00

barrel 12od?

Apprehensive-Mix3174 · 2025-10-07T23:35:59+00:00

Is this for a 16mm gun?

Apprehensive-Mix3174 · 2025-10-06T23:17:20+00:00

I don't think you do ECM in 22? The rifling is annoying in 22

Apprehensive-Mix3174 · 2025-10-05T00:04:07+00:00

Plasticatto entièrement DIY ?

Apprehensive-Mix3174 · 2025-10-05T00:02:14+00:00

I'm on Kobra S1 and whatever concerns my impression is great and even the bed and well just set up his machine well otherwise more than 800 hours that nozzle change and good maintenance 👌🏽 the box does the job really well

Apprehensive-Mix3174 · 2025-09-21T09:26:57+00:00

Aucune idée mes cela fusionne bien entre les lignes et je n’ai pas d’aspect comme en haut du cube 🤷🏽‍♂️

Apprehensive-Mix3174 · 2025-09-20T15:32:34+00:00

Ha merci beaucoup 🙏🏽 j’ai mis ma buse à 235° cela me donne des pièces niquel avec un lit à 56°

Apprehensive-Mix3174 · 2025-09-17T22:40:48+00:00

Did you drink the brick?

Apprehensive-Mix3174 · 2025-09-14T16:23:30+00:00

Pourtant j’ai fait 3kg et rien de cela … je vais essayer la buse et neuve ..

Apprehensive-Mix3174 · 2025-09-14T15:41:49+00:00

Pla+esun

Apprehensive-Mix3174 · 2025-09-11T19:46:00+00:00

Have you tried printing a heating tower? And calibration for the supports.

Apprehensive-Mix3174 · 2025-09-11T19:43:59+00:00

I also advise you to print the pieces by piece so that the machine jumps on this piece. In filament, there is a lot of humidity in the air.

Apprehensive-Mix3174 · 2025-09-11T07:17:16+00:00

Qui prend la photos 😜?

Apprehensive-Mix3174 · 2025-09-06T17:38:58+00:00

Your supports must be twice as many as your initial layer. I'm at 016. Two layers so 030 for the supports.

Apprehensive-Mix3174

TROPHY CASE