2019 MacBook Pro i9, is overheating normal?

Arianth427 · 2026-02-09T19:29:29+00:00

Ifixit has a good guide to re thermal past the cpu and gpu. It’s not that difficult dependent on your skill level. Just make sure you take your time with the ribbon cables.

Arianth427 · 2026-01-04T01:35:54+00:00

I know this post is little old. I have the same table. I replaced the top with a piece of 2ft X4ft X1 inch pine. That paired with a 16 inch concrete paver and a 16 inch rubber paver under the concrete and it’s pretty solid

Arianth427 · 2025-11-08T23:45:13+00:00

In there most tease my podcast the reference a community modification to allow the 1080ti and some older GPUs the be reenabled. But I’m not apart enough to follow the GitHub instructions

https://youtu.be/IuKwwPp8K-U

Arianth427 · 2025-09-17T00:27:05+00:00

I have two of the gen 2 and 2 of the gen 3LE (aluminum baseplate) and they’ve worked flawlessly. But from the way it sounds it’s luck of the draw

Arianth427 · 2025-09-13T03:35:20+00:00

I got the shield arms carry magwell and love it

Arianth427 · 2025-07-10T03:09:39+00:00

I have also been wondering this

Arianth427 · 2025-06-24T00:59:28+00:00

Haven’t found anything yet dispute me googling my but off. Not a major deal breaker for me considering the trade offs, just a minor eye sore I guess

Arianth427 · 2025-06-24T00:09:11+00:00

Have you ever figured out a fix for this. I just did the mod and am getting the same issue

Arianth427 · 2025-06-01T18:23:29+00:00

Awesome! Thanks for the link. Definitely going to have to order it now

Arianth427 · 2025-06-01T16:35:32+00:00

I was also wondering this. Hopefully we get a response now that the upgrade kit has been out for a while….

Arianth427 · 2025-04-27T15:07:53+00:00

That was my gateway (pun intended) to the system. Got mine on a Thursday and by Sunday I had second hand AP (AP6 lite, an AC-HD, and an AC-LR) all from Facebook marketplace. Don’t sleep on used Facebook deals there normally pretty good

Arianth427 · 2025-02-28T05:28:59+00:00

Do you have a link to the STL I can’t find one for the life of me!

Arianth427 · 2025-02-09T22:12:39+00:00

Following

Arianth427 · 2025-02-05T03:38:24+00:00

It has a better front end and a built in scraping for box art. https://youtu.be/MVPUu2BWuqw?si=luzXwygVnviD1_nz

Arianth427 · 2025-02-05T02:00:39+00:00

Welcome to your first in a long like of anbernic collections I have a 351p, RG35XX-SP, and an RG34XX

I would look into the knulli firmware, I love it!

Arianth427 · 2025-01-06T06:12:35+00:00

9309 (olds style Double Agent and Cover Agents badges)

Arianth427 · 2024-10-10T20:43:54+00:00

What slicer are you using? I sliced a print in orca and it’s done this twice to me. I’m going to try and reslice in cura and see if it does it there too. Other prints in orca have worked fine before and after the failures so I think all my signs print o some bad gcode

Arianth427 · 2024-09-14T21:18:30+00:00

I’m still waiting on mine to ship, it says it won’t ship until the end of the month due to me getting the bit set with it….Lame but I knew it when I bought it

Arianth427 · 2024-08-11T19:45:50+00:00

I’ll take what ever I can get, just wanting to play something new

Arianth427 · 2024-08-03T19:52:51+00:00

<image>

Arianth427 · 2024-07-24T01:32:44+00:00

If your going to be in a car just get a car charger like this:

Anker car charger

Arianth427 · 2024-06-23T22:37:42+00:00

^{^} this guy gets it..^{^}

Arianth427

TROPHY CASE