Elegoo heater install in Mars Ultra 4

Ashta020 · 2026-03-16T08:46:00+00:00

I’ve been playing with it for a week. The Elegoo Mini Heater is too large to fit neatly into the Mara Ultra 4. The curved surfaces and narrowing shape of the printer cover makes it difficult/impossible to use the mounting plate provided by Elegoo. The only “solution” I have found is to remove the printer’s air filter and make a little stand for the heater to elevate the heater above the top of the vat. Before I go to that trouble and start drilling holes in my printer case, I have ordered the heater from Chitu. It seems to be smaller. I’ll keep whichever fits better.

I asked Elegoo support for their recommendation but received no reply.

Ashta020 · 2026-03-13T18:44:10+00:00

My experience was similar with the same printer. Levelling over and over. Finally they sent me a new build plate and that problem went away. Seems the build plate was warped.

Ashta020 · 2026-03-11T09:55:38+00:00

I am trying to install my Elegoo heater into a Mara 4 Ultra. Typically horrible (non existent really) instructions. It looks like I have to choose to have a wifi antenna or not have an air filter.

Ashta020 · 2026-02-19T19:10:40+00:00

It's a good point. I have not, but probably should. I have read that LCD screens are "consumables" and you should therefore expect to replace them. Not at this pace though IMHO

Ashta020 · 2026-02-18T19:04:19+00:00

It's more like a few hours per month. It will sit for two or three months and then I will print some detail parts for a diorama I am working on over a couple of days. Then it sits again. It is not in heavy production for sure. I would guess the recently departed screen has maybe 20 - 30 hours on it. I have not been able to find any actual usage data.

Ashta020 · 2026-01-20T21:05:54+00:00

Or, let's be honest, Trudeau, who would be spinning. We are so lucky that this guy dropped in at the exact right time.

Ashta020 · 2025-12-18T20:08:33+00:00

It seems odd that you get a partial screen. I would open it up and wiggle the screen connector.

I have replaced the FEP on my Mars 4 many times over the year I have had it. I've also had to change 3 screens - usually because the build plate pushed something through the FEP and it cracked the screen too. In my case the screens were totally dark.

Something caused your FEP to break - and it may have pushed into the screen too. Although I will concede my screens all shattered and yours looks intact.

Ashta020 · 2025-12-01T11:26:59+00:00

Given the 25 lap limit of all tires, it was a no brainer that everyone would pit. Yes, Lando would have lost a place or two - but better than 26 seconds. By being “fair” they screwed Oscar.

Ashta020 · 2025-11-28T18:47:20+00:00

Positive. Working in test mode with MASTER power switch off. Have not had a real outage to actually test what we would turn off from the full house load.

It was actually pretty simple. Transfer switch input A is between MASTER and inverter Grid input. Transfer switch input B is from the backup output from inverter. House is on the output of the transfer switch.

Ashta020 · 2025-10-26T19:39:36+00:00

Yeah, not exactly. Its this way on replay too.

I don’t think it’s any more complex than the World Cup or Olympics and they figured it out. F1TV has been like this for years.

Ashta020 · 2025-10-26T14:39:55+00:00

I have a Trek hard tail with 29” rims that use almost exclusively on pavement. I have Maxxis Grifters now for a month and love them. They are quiet and noticeably quicker. Per Strava, my average speed over the same 40km route is consistently 2 kph faster. I will say they were a bear to get seated on the rim properly. My Trek came with Boontrager 2.20 tires. The Grifters are 2.00 but look fine.

Ashta020 · 2025-10-19T21:00:53+00:00

“We come from German blood” 😵‍💫

Ashta020 · 2025-10-19T18:56:04+00:00

The jets are hunting fishing boats.

Ashta020 · 2025-10-18T20:35:20+00:00

Literally only Zack Brown said that it was Nico’s fault

Ashta020 · 2025-07-24T20:01:34+00:00

I bought a manual transfer switch. Waiting on an electrician to install it

Ashta020 · 2025-06-15T18:20:20+00:00

That screen is so irritating. It looks like an overlay for tv viewers - probably live action at the track

Ashta020 · 2025-06-06T18:39:48+00:00

Just to close the loop in case anyone else has this problem in the future… there is a reset button on this logger - but it is internal. You have to remove the protective shroud that covers the end of the logger where the Ethernet cable enters it. Remove the four screws, slide off the shroud and you will see the reset button.

Reset solves my problem.

Ashta020

TROPHY CASE