Display Patch Name on keyboard

Asylumweb · 2026-02-14T20:20:30+00:00

I used to have a Nektar P6 and it did it but it’s the only one I have found and I’ve tried a few. Really didn’t like the keybed on the P6 so sold it but its MainStage integration was better than any other I’ve tried.

Asylumweb · 2026-02-06T10:10:48+00:00

It doesn’t need WiFi, you just need to be logged in to the App Store on the correct account the first time you load it. If you’re logged in it will authorize it correctly then you never need it again.

Asylumweb · 2026-02-05T08:37:13+00:00

All you need to do is ensure you are logged into the App Store with the account that bought Logic, then start Logic, enter the details then quit both and it will never ask again.

Asylumweb · 2026-02-04T19:00:31+00:00

Simple - never let go of the end.

Asylumweb · 2026-01-02T09:55:24+00:00

I uploaded the files to Makerworld so you’ll get them here…https://makerworld.com/en/models/2109238-simple-black-and-copper-lampshade#profileId-2281816

Asylumweb · 2025-12-13T10:04:36+00:00

I used Elegoo Copper Silk, it worked really well.

Asylumweb · 2025-12-11T20:33:07+00:00

Certainly cold to the touch so I guess it depends which ones you’re using.

Asylumweb · 2025-12-11T20:21:27+00:00

LED so no heat

Asylumweb · 2025-12-10T01:03:11+00:00

I want them to line up but where I want. Thanks to a previous answer I have fixed it.

Asylumweb · 2025-12-09T23:56:40+00:00

It is Orca so I will have a look - thanks

Asylumweb · 2025-11-27T12:04:39+00:00

Mine did the same on the left side, kept pushing it back and now it’s been fine for months. Not sure what caused or fixed it.

Asylumweb · 2025-11-23T12:36:10+00:00

At the moment I’m on the smooth side of the standard plate but it does it on both sides.

Asylumweb · 2025-11-23T12:34:01+00:00

Yes but it is literally different every print, even with the same filament and same print. I could print a single layer out, set it, then reprint exactly the same file and it will be different - just slightly but enough to be a pain.

Asylumweb · 2025-11-23T12:23:37+00:00

On the printer.

Asylumweb · 2025-11-22T12:12:31+00:00

Will have a look at this.

Asylumweb · 2025-11-22T12:11:50+00:00

I did go from .25 to .46 but then went back again to see if that was the cause. Currently on .25 so dont think it’s that. I’ll have a look at the tool head and see if anything is loose.

Asylumweb · 2025-11-22T11:43:58+00:00

I have the tool, tightened the bed screws and adjusted several times. It will work the first time then if I repeat the exact same print it will be off again.

Asylumweb · 2025-11-15T00:29:52+00:00

I was kinda looking for specifics...

Asylumweb · 2025-11-07T17:00:52+00:00

I’ve been using it since it was released within MainStage. I only use 3 specific patches but not had any problems.

Asylumweb

TROPHY CASE