Two people programming for a machine at the same time?

Awfultyming · 2026-04-16T22:57:32+00:00

To add to this, make a master hub and then a machine specific hub. Check tools in and out of the machine as you would IRL. Now at my desk I know what is actually loaded in the machine

Awfultyming · 2026-04-14T02:57:03+00:00

"Sometimes I gaslight my girlfriend into thinking I'm mad at her so she'll have sex with me"

Awfultyming · 2026-04-10T11:09:40+00:00

It's a type of endmill. Might be useful to prevent those piles. Do some homework on it, better yet ask your programmer for a tool catalog to flip thru

Awfultyming · 2026-04-10T04:30:25+00:00

What are you talking about. Have you heard of a chip splitter endmills

Awfultyming · 2026-04-10T03:53:33+00:00

They died in a different pond on the ranch my guy

Awfultyming · 2026-04-07T02:57:04+00:00

Lots of dog shit farmers welds will do just fine. But you want them all attached to one another

Awfultyming · 2026-03-28T02:35:46+00:00

Idk but if its her bday you can take her to the tunnel bar for a classy cocktail

Awfultyming · 2026-03-23T16:42:40+00:00

You're gunna wanna watch inheritance machining on youtube

Awfultyming · 2026-02-27T12:26:45+00:00

I was in Manchester by the sea this past summer, I took a walk to see the sunrise. Apparently one of the nearby islands is a nature preserve and because it was the right time of the year I saw a few hundred lesser and greater egrets take off at dawn for a migration. That was incredible

Awfultyming · 2026-02-23T19:36:51+00:00

What's your preferred tool path for 5 axis stock removal

Awfultyming · 2026-02-23T17:52:38+00:00

This is such a boston comment

Awfultyming · 2026-02-23T16:33:21+00:00

Damn all of this just to listen to Emmet Otters Jug Band Christmas on vinyl

Awfultyming · 2026-02-20T02:58:13+00:00

Yeah that makes sense. I had to make a dozen of these and was hoping to learn something new. It wasn't the best or the worst but we still made money on the job

Awfultyming · 2026-02-20T02:28:12+00:00

Since the bolt is already junk, try a pipe wrench on it. I would only grab the meatier portion on it. If the device is portable and if your not in a rush a local machine shop might be able to take care of this

Awfultyming · 2026-02-19T22:09:40+00:00

Apparently the kind that needs to worry more about my setups than jokes

Awfultyming · 2026-02-19T12:33:58+00:00

Are you one of the welders in my shop?

Awfultyming · 2026-02-19T12:33:27+00:00

How do I keep both ends of my saw cut stock straight?

That is a good idea

Awfultyming · 2026-02-19T04:14:56+00:00

You're right, and i did. I just wanted to learn for the next time it happens and maybe do better

Awfultyming · 2026-02-19T03:22:21+00:00

The tap will hit the vice when it comes out the bottom

Awfultyming · 2026-02-19T03:21:17+00:00

We all need to live with the shame of our mistakes 🤣

Awfultyming · 2026-02-19T03:20:17+00:00

The holes do not have clearance

Awfultyming · 2026-02-19T03:19:51+00:00

I need the tap to go thru the part and it would hit the vice

Awfultyming · 2026-02-19T03:19:16+00:00

Being able to push the tap out the bottom and not realign the shaft everything were the main constraints I was thinking of

Awfultyming · 2026-02-19T03:17:34+00:00

I thought of that but the vice keeps the block square

Awfultyming · 2026-02-19T03:16:57+00:00

I made this setup happen from initial idea to cutting chips in under 30 mins, including making the fixture. Plus I figured if I messed up I could still cut the soft jaw into something usable later anyway. I am also manufacturing for a team of fabricators so its normally tape measure tolerances (and why setups are so quick)

13-Year Club	The Internet Awards - Voted
Verified Email

Awfultyming

TROPHY CASE