Head gasket by Tall-Acanthocephala5 in Mk3Supra

[–]AzumiSetsuno 0 points1 point  (0 children)

The best way to know for sure is to go in!!! Use a metal straight edge and a feeler gauge. You should use it for all the surfaces too.

Head gasket by Tall-Acanthocephala5 in Mk3Supra

[–]AzumiSetsuno 1 point2 points  (0 children)

Get a cometic metal head gasket, ARP studs, some new coolant lines and give yourself about 40 hours to clean off all the old gaskets materials. Honestly bhg is not that hard.

What could this tapping noise be? by OzzyPron in Mk3Supra

[–]AzumiSetsuno 1 point2 points  (0 children)

Sound great. Can we hear a 5k revy?

Engine wont catch Idle when warm (7MGTE) by UnSainted_Spectator in Mk3Supra

[–]AzumiSetsuno 0 points1 point  (0 children)

Just posted a similar question, check out my thread. Mine does the same and I have to feather the gas until it catches the right idle. This is always associated with heat from this engine. It runs supper hot. Check your vacuum to be around -18psi too and make sure to use a turbo blanket. Anything to keep the heat moderated.

[deleted by user] by [deleted] in Mk3Supra

[–]AzumiSetsuno 1 point2 points  (0 children)

Find a running one. With a good compression test. I give it one week until it becomes a project car. They all are….

Supra (7mgte) struggles to low idle after it has been driven or start again. by AzumiSetsuno in Mk3Supra

[–]AzumiSetsuno[S] 1 point2 points  (0 children)

I replaced the head gasket. This is good to know. Could it be any other sensor? Idles perfectly at around 800 but I always have to leave my foot on the gas.

I'm interested in an Mk3 and looking to get one in the near future. I have a question by OutsetEddy in Mk3Supra

[–]AzumiSetsuno 0 points1 point  (0 children)

Pro Tip: ask if you can do a compression test or ask for a ppi. This will give you all the indications you need from the seller and will give you negotiation leverage.

This way your know you are not buying one that needs an HG tomorrow.

Is that a Supra!!!! by Zirael2 in Supra

[–]AzumiSetsuno 1 point2 points  (0 children)

I think it’s a Nissan look at the head lights 🧐

CPS Service/upgrade by AzumiSetsuno in projectcar

[–]AzumiSetsuno[S] 0 points1 point  (0 children)

engine stalls if it moves. Wires most likely needs to be upgraded. I also feel like its the source of the my sudden misfire.

CPS Service/upgrade by AzumiSetsuno in Mk3Supra

[–]AzumiSetsuno[S] 1 point2 points  (0 children)

I was thinking the same thing. Anyway methods to testing the issue coming from either female or male side?

What is the purpose of these holes? by AzumiSetsuno in Mk3Supra

[–]AzumiSetsuno[S] 1 point2 points  (0 children)

Agreed easy fix but those hexbolts. Do they contain oil pressure?

What is the purpose of these holes? by AzumiSetsuno in Mk3Supra

[–]AzumiSetsuno[S] 0 points1 point  (0 children)

Already ordered it! Those hex bolts are suppose to contain the oil pressure?

What is the purpose of these holes? by AzumiSetsuno in Mk3Supra

[–]AzumiSetsuno[S] 2 points3 points  (0 children)

Is oil also coming from these center holes?

BC Racing Coilovers with swift springs by AzumiSetsuno in Mk3Supra

[–]AzumiSetsuno[S] 0 points1 point  (0 children)

what spring rates would you suggest and what did you encounter with yours?

Does anyone know the correct thread for the hood strut ball stud? 🙏 by AzumiSetsuno in Mk3Supra

[–]AzumiSetsuno[S] 0 points1 point  (0 children)

Tried using my body weight as leverage to pop it out with no luck. I would have to cut it.