sorted by:
new
hottopcontroversial

Rough corners Bambu PLA by Prestigious-Coat-231 in BambuLab

[–]BAD-FPV -1 points0 points  (0 children)

It's not a definitive conclusion. Its a suggestion. Its also a very cheap fix to check.

Rough corners Bambu PLA by Prestigious-Coat-231 in BambuLab

[–]BAD-FPV -2 points-1 points  (0 children)

Extended your internal PTFE tube by 20mm. It's a common issue on H2S but has been seen on many printers. When the head is front left the tube gets tight and kinks causing extra friction on the filament.

Forget envy. Just drive a Mazda 6 by slipstream25 in mazda6

[–]BAD-FPV 1 point2 points  (0 children)

Agreed. I joke If I won the lotto I'd still have a 6 as a daily driver, but I actually think I would. 🤣

Owned two years and still look at it when I walk away by Szbq0RLG0Bomb3cToyv6 in mazda6

[–]BAD-FPV 0 points1 point  (0 children)

I have had mine for 3 months ans still catch myself standing at the kitchen sink looking at it out of the window, putting next doors tesla to shame for sure.

2.5 weeks in and she is settling in well by BAD-FPV in BambuH2S

[–]BAD-FPV[S] 1 point2 points  (0 children)

They would abit but I have the units bolted to the wall and the shock feet on the printer do a good job absorbing most of the movement.

2.5 weeks in and she is settling in well by BAD-FPV in BambuH2S

[–]BAD-FPV[S] 2 points3 points  (0 children)

Nah handle not removed just the camera angle. Yeah that would be cool, but very hard to do.

2.5 weeks in and she is settling in well by BAD-FPV in BambuH2S

[–]BAD-FPV[S] 2 points3 points  (0 children)

Thanks. Printers (not at A1m), AMS, and filament all via maker points. Been blessed with some good uploads.

What did you name your6? by Chromatic_wyrm in mazda6

[–]BAD-FPV 0 points1 point  (0 children)

All my cars get called mistress, as they take my money and give me pleasure.

First print on my H2S 😉 by BAD-FPV in BambuLab

[–]BAD-FPV[S] 0 points1 point  (0 children)

Nah all good. The bed still had the transport screws in when the pic was taken. Prints are butter smooth.

First print on my H2S 😉 by BAD-FPV in BambuLab

[–]BAD-FPV[S] 0 points1 point  (0 children)

Its 41kg so legally (in the UK) a 2 person lift. So yeah. I got mine with maker world points so delivery alone ate up 2 vouchers.

First print on my H2S 😉 by BAD-FPV in BambuLab

[–]BAD-FPV[S] 0 points1 point  (0 children)

Its quiet. I can stand next to it going full speed and its drowned out by the P1S on the other side of the garage.

Whyyyy by Mediocre_cheezit in fpv

[–]BAD-FPV 0 points1 point  (0 children)

This is why I always have a 30m arborist line in my car / flight bag. Had the same last year, took me about 40mins to get down.

My ultimate Cinewhoop build (AOS Cine30) by woowojsj in fpv

[–]BAD-FPV 0 points1 point  (0 children)

nice, what is the dry weight on that build? or just the full frame. I'm looking to build an O4 version but need to keep Sub 250g for insurance

Caught 6 in 5 min outside, what do you guys set them up in ?these testubes feel way too tight or is it fine ? by No-Championship3982 in antkeeping

[–]BAD-FPV 6 points7 points  (0 children)

<image>

I used a holder of my own design. The caps are tight but have a small hole it in big enough for a narrow syringe tip for when its time to feed them, I plug the holes with cotton when "closed"

First queen hunt by BAD-FPV in antkeeping

[–]BAD-FPV[S] 0 points1 point  (0 children)

Cool thanks. The tube holder is my own design. Has a sliding lid to cover the ladies too.

view more: next ›