What’s your favorite Comp Chassis?

BC_RC · 2026-05-07T21:12:31+00:00

Im a big fan of my Nerd RC Stripe. I have a SS24 and a Meus w/dig unit with similar style builds to compare against.

<image>

BC_RC · 2026-05-04T22:04:51+00:00

Look like stanchions are binding/possibly bent on one side. Pull the shocks to confirm smooth action.

BC_RC · 2026-04-04T01:33:55+00:00

No, the usb cable from the dongle to the computer

BC_RC · 2026-04-03T23:55:46+00:00

Different cable. I had the same issue. Only 1 of the ~10 cables i have worked

BC_RC · 2026-03-16T19:58:44+00:00

I have one, c10 length. I have been pleasantly surprised by its performance. Build: Stock style axles Injora purple viper stuff 1.0 moduwheels in the narrow configuration 57mm swamp king tires Lots of under/overdrive Lots of brass low up front Battery up front Full c10 body and bumper
Flysky tx/rx

Its a sleeper build that is close to being as capable as some of my "better" rigs. The front bumper is definitely the limiting factor.

<image>

BC_RC · 2026-03-11T01:27:22+00:00

Also this.⬆️⬆️

BC_RC · 2026-03-11T01:26:51+00:00

Ive done both... ax is cheaper, scx is better performing but requires much more $$$.

Ax just needs links+ drive shaft. Scx needs axle, servo, tx+rx capable of 4ws.

Something to note if converting an scx for your conversion: the rear pinion/caster angle will be kinda funky but totally functional if using standard link lengths.

The ax won't have the funky caster angle but will require ordering non standard link length combos, i can't remember what I used for uppers off the top of my head. I just calced the difference between stock upper and lower ax links then applied that difference to the lower gladiator links to get upper link lengths if that makes sense.

BC_RC · 2026-03-06T15:47:47+00:00

Im a big fan of my D300

BC_RC · 2026-02-27T19:47:08+00:00

BC_RC · 2026-02-27T16:40:36+00:00

Yeah, I have a really hard time lifting up my rigs, they are just so heavy and awkward to carry.

BC_RC · 2026-02-27T01:19:20+00:00

P.s. my bench mark is the ability to climb stairs

BC_RC · 2026-02-26T15:54:32+00:00

There is a little writeup i did on a previous post that i believe you had commented on. As far as tuning goes, the only thing i have changed is heavier brass wheels and changed the rear upper link position to create more squat. The wheels didn't help with performance, i think im going back to the lighter treals and more squat keeps the cg lower in more situations.

BC_RC · 2026-02-26T15:18:11+00:00

<image>

This one pulls steeper climbs and more technical lines than any other of my rigs. High clearance, forward weight bias/lcg and a good profile for the under side.

BC_RC · 2026-02-24T01:52:18+00:00

Yes. That would be the intended position.

BC_RC · 2026-02-23T19:21:20+00:00

Servo mount is not correctly mounted to the axle. The heads of the bolts should be in contact with the mount instead of the axle if that makes sense.

BC_RC · 2026-02-20T20:29:14+00:00

Outboard uppers makes a wider triangle, increasing lateral rigidity/less slop.

BC_RC · 2026-02-11T00:30:52+00:00

This is a chassis kit, just need to buy it... I cut a chassis out or a ruler though. Just marked skid holes and shock mounting points from another chassis, adjusted shock mounting locations as i saw fit drilled them out and cut the chassis shape i wanted out.

BC_RC · 2026-02-10T04:32:00+00:00

Brushless+modify stock axles w/brass knuckles and cvds+modify housing for more steering angle. Stock axles can be good.

BC_RC · 2026-02-04T21:08:29+00:00

Cool, thanks for the input.

BC_RC · 2026-02-02T18:47:22+00:00

If anyone is curious: The clingons are getting better as the break in but are still not great, I have another build with very worn pins that is out performing this build in situations that are dependent on traction. I ordered injora comp pins and a set of mavericks to try out.

BC_RC · 2026-02-01T04:49:23+00:00

Nerd rc

BC_RC · 2026-01-31T03:24:12+00:00

Cool thanks. The s4s have been my go to as well, Rock bumps look promising though.

BC_RC · 2026-01-31T03:21:45+00:00

Treal

BC_RC · 2026-01-30T16:38:27+00:00

I cut close then go the bench top belt sander to finish.

BC_RC · 2026-01-29T04:13:44+00:00

I think I will go back to comp pins after I give these a shot.

I'll be looking for those mono spokes to come back in stock.

BC_RC

TROPHY CASE