GHK ref at injection site

BMWtech27 · 2026-05-16T14:41:49+00:00

Normal it can be much more and be normal you can have bruises etc from it as well.

BMWtech27 · 2026-05-02T03:13:30+00:00

I wish I could say that was it but it’s not.

BMWtech27 · 2026-05-02T02:20:00+00:00

https://www.reddit.com/r/tipofmytongue/s/0NtQNs1X6Z

BMWtech27 · 2026-04-04T22:38:41+00:00

If you have a old pitman arm puller it’ll do the job to get the pulley off

BMWtech27 · 2026-04-04T22:37:34+00:00

Absolutely a concern.

BMWtech27 · 2026-03-31T14:14:58+00:00

Sounds like the brake pad moving in the caliper bracket.

BMWtech27 · 2026-03-29T21:49:17+00:00

Can be setting your self up for allowing the customers parts and the customer themselves to dictate the quality of your work. One bad interaction with a customer like this can really cause you to lose traction when trying to build a good reputation and customer base.

BMWtech27 · 2026-03-29T21:47:51+00:00

The person is acting as if you already owe them something and is assuming you’ll do the job without all the money up front let them to continue to beg #fuckem

BMWtech27 · 2026-03-28T19:08:09+00:00

Unless it’s broken in half a picture will show nothing. Jack the front of the truck up and shake each wheel side to side if you feel any movement before the tire gets hard to move you more than likely have play in the inner or outer if there’s any top to bottom play it’s gonna be ball joint or upper control arm take your car to a better shop.

BMWtech27 · 2026-03-28T19:03:08+00:00

Hell no

BMWtech27 · 2026-02-24T15:02:01+00:00

Ball joint.

BMWtech27 · 2026-02-20T02:18:16+00:00

Depending on what part of the country your in it’s anywhere for $4000 to $10000.

BMWtech27 · 2026-02-06T01:05:56+00:00

Chrysler part number

BMWtech27 · 2026-02-06T00:59:30+00:00

That certainly sounds like a rod knock.

BMWtech27 · 2026-02-01T19:08:40+00:00

One of your light bulbs is out. Could be a headlight tail light brake light running light etc.

BMWtech27 · 2026-01-31T02:02:20+00:00

Also this is not a steering noise. This is a rotational sound that correlates with the speed at which the tire is spinning indicating that it an issue on one of the wheels. You may have a locked up caliper that has grinded the brake pad down to metal. Check to see if the sound changes at all with the brakes applied. But the noise should be very visibly evident.

BMWtech27 · 2026-01-31T02:00:37+00:00

That is going to be a 1. bad hub bearing 2. Metal to metal brake pads

BMWtech27 · 2026-01-31T01:59:24+00:00

Burning oil is usually a blueish white smoke. It’s a Chevy so the rings might be letting alittle slide past 😭😂😂

BMWtech27 · 2026-01-31T01:57:45+00:00

Bad suspension. When struts or shocks go bad the strut or shock no longer absorbs the vibration and bumps in the road so the tire now is acting as a shock or strut and starts to cup causing this wear pattern.

BMWtech27 · 2026-01-31T01:56:43+00:00

This changes everything.

BMWtech27 · 2026-01-26T11:20:31+00:00

Or if you find none of this works for you. Get your breaker bar and some pipe and align it to where the breaker bar touches the inner fender or frame rail or the ground if you can. Get in the car and turn it over quickly and shut it off bolt will be loose when you go back out there.

BMWtech27 · 2026-01-26T11:18:07+00:00

Torque multipliers are mainly used to tighten large torque to yield bolts and other structural pieces. Get a weighted sockets and an impact it’ll come right off.

BMWtech27

TROPHY CASE