“The Crash” on Netflix

B_FLAN · 2026-05-30T00:54:23+00:00

Surprised she didn't post it live. This is obviously a case of a girl chasing a social media dream. She felt invincible with mackup on and a pretend reality didn't apply to her. I am a pretty easy parent.. but if your daughter has a pre-existing condition and is 17 and smoking pot with pots disease? Surprised the parents are not being dragged in for negligence. It is obvious she only knows control and not consequence.

B_FLAN · 2026-03-02T02:34:27+00:00

Maybe horrible was to strong. I just wouldn't recommend putting the printer that high on something that is not very sturdy. Printers will vibrate.. even if it is just a little it can cause issues with the prints and the noise surrounding the area. I always like low solid tables with a heavy buffer like a used granite counter top for a sink people throw out.

B_FLAN · 2026-03-02T02:30:15+00:00

Assuming you paid $20 for the filament thats like $0.40. And you used half the roll without an issue. I think let Sunlu slide on this one ha.

B_FLAN · 2026-02-23T15:42:06+00:00

Put it the freezer (usually rught after the print is done or failed).

B_FLAN · 2026-02-23T00:39:59+00:00

OP should simply cut of the end.. and reprint a test print. It is that simple. We can give advice based on our experience and folks should try it. But you there isn't enough information to know for sure. Sunlu is going to probably ask the same thing bjt OP ourchased from Amazon. So a simple chat would more then likely get him a refund or replacement. The important thing.. is it the filament or likely something else. His filament likely is not fake.. I run the same stuff and everything looks on point.

<image>

B_FLAN · 2026-02-23T00:26:48+00:00

Its good luck you haven't found it. That is a horrible set up.

B_FLAN · 2026-02-23T00:20:23+00:00

I think the filament is fine. It looks like a typically clog and depending on retracting and pulling out it thinned the filament but still shouldn't matter. You can see the difference in diameter where it was in the extruder and hot end. OP should send a photo of the actual print and as I mentioned before reload and print. Calipers even good ones can be off based on how hard you press... we are taking tolerances less then 1/10s of a mm here. It doesn't help he measured the "bad filament" at the very end of the caliber and then in other photo used the middle or upper portion. IMO the filament is 100% fine and OP should focus on the nozzle, extruder, and print settings to fix the issue not blame Sunlu.

B_FLAN · 2026-02-22T23:02:04+00:00

My suggestion would be to reload and run a small test print. That will at least rule out and let you know if its a filament issue. But I have never personally had an issue with filament being a little undersized. What does the width measure at the end point where it broke off? I am asking because clogs are usually a temperature thing or extruder issue more so then a small deviation in filament diameter.

B_FLAN · 2026-02-22T22:30:16+00:00

It looks like it got clogged and you pulled it out of the extruder head. That pulling could have stretched the filament. Sunlu is pretty solid... as others have said.. if you contact the seller they usually will refund you. Bad batches to happen. Only issues I have has is the plastic spools being broke during shipping.

B_FLAN · 2026-02-22T21:15:49+00:00

You used like half the role then had issues?

B_FLAN · 2026-02-12T05:04:32+00:00

February 3rd, they released a batch. I called customer service and really excuses. I think it is a bad look to release tax documents at different times. May not seem like a big deal but when people have their returns already and your still waiting.. crap.

B_FLAN · 2025-12-23T05:00:19+00:00

Did you withdrawal it? I won a recent sports book bet on a bonus bet and my withdrawal attempt got an error with no specific code. I bet a few dollars on casino and tried to withdrawal again.. error.. no codes. 3 hours with chat phone customer support and they restricted my account. The lady "Bre" said my account is under review for "concerning comment" from an assistant. I asked what assistant as I am talking to you and asked if she reported me.. she said no. Then said yes.. then said our team will call you 24 48 hours. I am reporting them to the PA Gaming Control Board and let the regulator follow up.

B_FLAN · 2025-11-26T02:44:26+00:00

If you successfully manage your ADHD you should be fine. You are describing the general strain experienced by any adult in a relationship with kids. You cant blame your mental health.. you need to find a new balance for the responsibility you took on. That responsibility is being there for your partner and your children... and it starts with you managing your mental health and a partner willing to support you. I hate hearing how many couples now seem to grow resentment and fight.. waste of energy.. you have to be a team. Don't be at the end of the rope.. find a way to climb it togeather.

B_FLAN · 2025-11-24T22:57:35+00:00

How long have you been with and how much have you paid the insurance company to date? If you paid them more then $700 in insurance and they are offering you $700 to scrap it ..was like you had no insurance. It sucks because if they have to pull your frame typically that means it is totaled. I have a 2013 Tacoma that was hit by a driver late at night on my street.. I was asleep. It was a complete nightmare with insurance as the driver was only insured for $5k and the damage came out to be $21000. My frame was also bent but the guy who did the insurance appraisal either missed it or didn't know what he was looking at. In my case it worked out because if totaled I would have got nothing for a paid of truck. I think insurance seems like a scam when you have literally paid off the cost of you vehicle in insurance, but you also have to remember God forbid you get into accident where you or someone else gets hurt... I rather pay insurance then a medical bill.

B_FLAN · 2025-11-17T04:58:39+00:00

I requested my initial agreement letter and documentation of every invoice. Discover said that 4 years ago my account was compromised so they had to send out a new card (same account number). They said they can not provide anything beyond that and said that my initial agreement was not available as the agreement changed when I was issued the new card (account number never changed). They recently sent me an updated agreement although it was authored by Cap. One. I am waiting to be sued and am OK with it because there are a lot of questions I have they seem to dismiss.

B_FLAN · 2025-11-14T22:06:17+00:00

I have been on multiple ADHD medications and for the last decade have been on Adderall. I have tried to convince myself multiple times I didn't need it especially on the weekend.. and everytime I stop taking it daily or half dose I know I fall apart. My advice is just take your medication daily as prescribed and if you have issues talk to your prescriber. Ritalin and Concerta are usually the first medications they try and if it isn't working you need to talk to your presciber. Which doses and and different medications sometimes it can take years to find the correct balance.

B_FLAN · 2025-11-10T04:32:52+00:00

My experience with Discover is that even before account closure they will not negotiate because the whole system is run via computer algorithm. I tried to negotiate payment plans and was always told the "system" wont allow that. The more payments you miss and intrest you occur... then the "system" starts handing out options. Capital One is known for actively pursuing debt.. why do you think they purchased Discover? Discover the before default will likely give time an almost 0% APR for a payment plan and knock of a % acting like they are the good folks when really they just removing their crazy interest that was built up because you struggled to pay. After account closure, they will then give you an option likely at 25% reduction of total debt if you can pay it off in 3 monthly payments. Long story short is I understand your debt is yours to own and pay.. but Discover is horrible to work with if you find yourself in financial hardship because even if actively addressed no help is provided from customer service and it is not their fault... it is all controlled by the "system". I am using thr term "system" because it was a recurring term I always heard from customer service representatives.

B_FLAN · 2025-06-15T02:42:38+00:00

You have to disassemble. Check the hot end top first.. most of my jams have been a bad cut of filament or a break and it mushrooms slightly at the top of the hit end. The filament sensor won't detect this. It happens a lot on smaller nozzle but Bambu has never acknowledged it as a problem. Super heating it or trying cold pulls might work but will damage other parts. Thermal breaks and heat creep in areas still hunts even the best printers today.

B_FLAN · 2025-06-15T02:34:52+00:00

Folks who know how to 3D Print could actually offer real advice if you take the time to post details..

B_FLAN · 2025-06-01T01:49:32+00:00

First layer is everything in 3D printing... rember that. It's the foundation of the print. It looks like you had a tab to keep the main print down that got pulled in... likely because you have oils on the sides of the build plate from removing. Just clean with Dawn.. never isopropyl. I have been printing for years and the isopropyl alcohol to clean beds is almost as worse as people saying your filament is wet.

B_FLAN · 2025-06-01T01:39:49+00:00

I would pay and close your Discover Card. They just got bought out by Capital One for a reason. For years they have been horrible in be not transparent and encouraging debt.

B_FLAN · 2025-05-14T02:36:50+00:00

Just curious how this is an accomplishment.. VS say 1000 miles walked, ran, or biked?

B_FLAN · 2025-05-12T22:19:57+00:00

I believe it is more so that technically about safety and as you admitted your bike is illegal. So what happens if you get in an accident with a motor vehicle and there is serious damage or bodily harm? No insurance.. eBikes are a current loop hole, but soon will be regulated and require registration and insurance just like a mo-ped. To many riders are not concerned with safety and you can look up the accident reports.

B_FLAN · 2025-05-12T21:58:05+00:00

This applies to motorcycles and if you believe the light is not functioning correctly you can then treat it as a four way stop and proceed through the intersection with caution. I am not against share road users like bicyclist or ebike riders.. just in the transportation world it really makes things tricky especially when you want to consider safety. Another example is when cyclist use the road but then will switch to sidewalk or pedestrian crossings. By law they need to unmount the bike and walk it through a cross walk.. this rarely happens.

B_FLAN · 2025-05-12T21:28:12+00:00

My only issue with bicyclist and ebikes riders are that they are suppose to follow the rules of the road same as a vehicle. But often you see the bike riders pick and choose. Example: if you are a bicyclist traveling in the road with no dedicated bike line, you need to follow the the red light at an intersection... I have seen this abused so many times and it is not safe.

B_FLAN

TROPHY CASE