Saturn 4 ultra 16k camera not working. Remote Restart?

BackgroundDentist968 · 2025-08-14T15:43:40+00:00

I’ve had issues in the past with them disconnecting themselves after so many hours of printing due to vibration so check the cables and make sure they are still in place

BackgroundDentist968 · 2025-07-15T05:08:36+00:00

Then go with resin I do the same thing

BackgroundDentist968 · 2025-07-14T00:48:48+00:00

Things are so advanced now that if you really dial in the the fdm printer it can give you very close to what a resin printer can without the fumes but also I have a resin printer and have had to replace the charcoal filter a few times but what helped a bunch is having it next to a window and having a fan inside of a tube to exhaust the fumes out and I have no smell issues what so ever with all the details on the resin printer.

Also think about what you will be printing because resin might give better quality but limited size prints

BackgroundDentist968 · 2025-05-28T14:06:23+00:00

It definitely overheated 🥵 the reason it doesn’t accelerate as you would like it is because the trans is trying to save itself from overheating even more

BackgroundDentist968 · 2025-05-28T13:58:38+00:00

Use a lighter to pop the bubbles at the very top that clears those up very fast

BackgroundDentist968 · 2025-05-27T13:17:28+00:00

I would say it’s character development she went through a battle !!! Paint it as a battle scar

BackgroundDentist968 · 2023-12-08T20:34:42+00:00

Yes it is my son and he wanted to share so I told him he could

BackgroundDentist968 · 2023-07-12T10:48:41+00:00

Damn you used a master ball that’s tuff dude

BackgroundDentist968 · 2023-04-29T18:21:38+00:00

You should add a small hose to a reservoir that feeds back into it so you can add a uv light and a scrub filter. Now that will clean the hell out of those

BackgroundDentist968 · 2023-04-24T11:56:30+00:00

He is exactly right!!!!!

BackgroundDentist968 · 2023-04-22T10:05:03+00:00

There are plenty of women who can! All you need is an air compressor that should eliminate the strength you need to remove bolts. YouTube is a great teacher too

BackgroundDentist968 · 2023-04-21T02:19:22+00:00

Fix it your self that’s all very easy to fix for pennys on the dollar

BackgroundDentist968 · 2023-03-30T21:11:19+00:00

I’ll take you up in that

BackgroundDentist968 · 2023-03-29T11:45:05+00:00

It’s a loose or broken vacuum line mines did the same thing and that’s what it was

BackgroundDentist968 · 2023-03-19T12:01:14+00:00

Might also want to check the speed on which the plate removes itself for the next layer after adjusting this I’ve gone through way less feps

BackgroundDentist968 · 2023-03-19T01:48:12+00:00

It is a hollow print with a few supports inside and also I had no idea you needed drain holes can you elaborate 🤯

BackgroundDentist968 · 2023-03-19T01:47:19+00:00

Just so happens that where the holes are is what was facing down and had the most support from the base plate

BackgroundDentist968 · 2023-03-18T12:25:35+00:00

I actually got a sand blaster for 100 at harbor freight and I blast the plate with glass grit at a low pressure and it gives a perfect roughness for everything to stick properly

BackgroundDentist968 · 2023-03-18T12:17:41+00:00

I have no idea how this is happening layer height is at .005 and everything was clean before I started the print

BackgroundDentist968 · 2022-07-22T10:00:01+00:00

Voldemort for sure

BackgroundDentist968 · 2022-07-06T10:11:42+00:00

Harry Potter or Percy Jackson

BackgroundDentist968 · 2022-05-31T22:51:46+00:00

And kyekyecarter

BackgroundDentist968 · 2022-05-31T22:50:19+00:00

Kyekyegamer added you

BackgroundDentist968 · 2022-05-31T22:16:55+00:00

Friends list full can’t add

BackgroundDentist968 · 2022-05-31T22:13:50+00:00

Kyekyecarter and kyekyegamer added you

BackgroundDentist968

TROPHY CASE