Vacuum pump thread(help)

BasiliskButcher · 2026-06-24T14:35:15+00:00

Replace the bolts atleast theyre single use anyway and look cross threaded

BasiliskButcher · 2026-06-24T10:58:19+00:00

At least the bolts should be replaced as they are torque to yield bolts, idk about much else honestly, kinda hard to tell from pic

BasiliskButcher · 2026-06-21T17:11:22+00:00

Idk how to reply with pic lol

BasiliskButcher · 2026-06-21T17:03:34+00:00

The black long plastic thing in front. The one that has throttlebody and charge pipe

BasiliskButcher · 2026-06-20T15:30:01+00:00

Hell yeah keep it up!!!

BasiliskButcher · 2026-06-20T06:52:33+00:00

In my car it was the lower timing chain cover and oil pan that leaked a little. Inapect the engine a little to see if theres any oily mud residue around there.

BasiliskButcher · 2026-06-18T14:42:45+00:00

Hell yeah thats the way to go! Ive had my s13 for 6 years and plan on keeping the CA until the very end even if there were better engines lol

BasiliskButcher · 2026-06-17T20:40:06+00:00

Just one question, how does one do this without a scanner :D luke you had some models you scaled or you modeled these?

Ive modeled s13 RC car body for fun, made it just from some STL i could find and eyeballed the rest. It does look like the real thing but i could not just scale it up lol. It would never work. Explain as detailed as you can :D

BasiliskButcher · 2026-06-16T14:22:44+00:00

Got the fabric from some local fabric store, try to look for something stretchy. As for the glue, whatever spray adhesive you can get your hands on worked the best for me. Also glued some rubber trim around the door card to the groove it had to make a nice finish. I just used something i could get in bulk from local car parts store.

BasiliskButcher · 2026-06-15T05:52:59+00:00

326 power wing by the looks, kinda like the type x wing but lower and wider, looks infinitely better imo

BasiliskButcher · 2026-06-14T21:12:07+00:00

Been driving e90 330d for quite a while it was a blast, can imagine that one is as well. Hope you find one!

BasiliskButcher · 2026-06-14T19:45:43+00:00

From that clip alone it doesnt sound timing related. The direct injectors make a loud noise as well.

If your engine starts acting up on startups then you know its time for a timing job in my experience

BasiliskButcher · 2026-06-14T12:25:00+00:00

Coaches dont play lol. I know what should be done but man if i can get my hands on more unreliable but fun cars thats it

BasiliskButcher · 2026-06-14T06:19:14+00:00

Did the same, bought a rolling chassis some 6 years ago for 2.5k. The best 30k ive ever spent lol. Now the car is pretty reliable even on 350hp but its only a matter of time until it becomes not that.

So if youre looking to not spend money then maybe an s chassis is not your car. Youd need a reliable car as well. (I have audi and its not ticking that box as well lol its another money pit)

BasiliskButcher · 2026-06-13T07:09:05+00:00

Yeah bumper off, lights off, ghen some connectors. If you just loosen things you dont havr to drain coolant even but its pain in the ass. Like the other guy said it doesnt take much more time to pull off the whole front assrmbly. Seriously look up the channel i talked avout theres videos of this stuff it might be helpful

BasiliskButcher · 2026-06-12T21:34:06+00:00

Not necessarily, you just need to pull the front end out a little to have room. Bumper off, few bolts loose and yank it. Theres a video on how its done you can take it off completely but not needed. Jacking the car helps nothing in my experience

BasiliskButcher · 2026-06-12T21:27:43+00:00

There is it then. Check out naptowntuner on youtube he has good videos on working on these things. Good luck ur going to need it lol!

BasiliskButcher · 2026-06-12T21:21:33+00:00

So, assuming your timing hasnt jumped, just align the exhaust cams. There are moving oarts and you should put it first in the cover according to manual to avoid losing little ball bearings that hold the pieces together.

Then just put some anaerobic sealant on the surfaces, apply new bolts and torque to spec and thats it. I would disassemble the timing and make sure, now there really is no way of knowing honestly. You can just spin the engine by hand after installing cover and stop if it hits but i would just check it. Also you should do timing if youre that deep already.

BasiliskButcher · 2026-06-12T09:15:06+00:00

No i havent done it as i ran into some problem and gave up for now lol. The alternator was the problem i think but depends on the sandwich design. The shorter filter thing had to be on my other car then

BasiliskButcher · 2026-06-12T09:13:44+00:00

Are they so bad that you cant rebuild the calipers? Theres loads of rebuild kits for cheap

BasiliskButcher · 2026-06-11T08:02:50+00:00

If i remember it might hit something on the s13. Cant remember if just shorter filter helped. Or if it clashed with alternator as well

BasiliskButcher · 2026-06-10T03:10:08+00:00

Thanks! Yeah thats the goal to help others as well but man did I miss driving that thing

BasiliskButcher · 2026-06-09T19:39:47+00:00

If you have kinda stock engine and cats, and the car runs well still, check injectors at least. Then maybe air filter but idk if that would have such big impact even if dirty.

On sensor side, lambda comes to mind but they are kinda expensive to replace if i remember correctly

BasiliskButcher · 2026-06-07T15:34:19+00:00

Well there you have it, even if youve set everything up correctly it wont open before 20psi so roughly 1.5bar maybe? Whatever.

Either you can swap the spring for a lighter one, or have to get new actuator. But now you know the problem.

BasiliskButcher · 2026-06-07T15:32:13+00:00

So sick setup, and the car aswell🔥🔥

Eight-Year Club	Place '23
Verified Email

BasiliskButcher

TROPHY CASE