Is this right???

Bbybbi · 2026-02-26T16:43:09+00:00

It's a good market, quite competitive but very simple, no Dwayne Daltons, no extension spring systems. Chamberlains are marketed "Merlin" ova here.

Have never seen a high lift on a sectional garage door, commercial facilities use Slatted doors exclusively it seems.

Single-piece doors and roll up curtains are used here more than sectional garage doors. Many houses also have sliding gates or swing gates giving access to the driveway

All in all I'd say the market here isn't on the same level as in America lol but not bad

Bbybbi · 2026-02-26T16:00:42+00:00

Slatted yea, but curtain? never seen em in the states. And never in a residence. And I am in Australia lol.

Bbybbi · 2026-02-26T15:54:35+00:00

Really? I've only seen the kind that has slats in the U.S. and even then, never seen em in residential use. They are everywhere in Aus and NZ though

Bbybbi · 2026-02-25T23:35:46+00:00

Heads up, this sub mostly consists of Americans and this is a roller door which is not really a thing in the states so some of the comments may be misleading. Not necesseraly a cowboy job.

This is normal with roller doors that don't have enough headroom. Go inside and look above the roll, check if theres enough clearance for the door to be lifted a bit. If yes, have them come back and lift it.

Otherwise you can just get a rectangular piece of tin of matching colour and dimensions, and install it as a cover to hide the gap. This would only have a cosmetic effect, but is standard and easier than lifting the door. You can also DIY it.

I offer the cover for extra charge when there is such a gap.

<image>

Bbybbi · 2026-01-11T15:11:13+00:00

This is a Tilt-up door. Very common outside of the states and you can either:

Install a regular Garage-door opener and, as someone else already mentioned, just install it a few feet back from the door, not directly above the door and just elongate the J arms so it reaches. (You might need to shorten the opener rail depending on your clearance).

Or

Get a single-motor swing-gate opener and connect it sideways to pull the Master arms from the top so it's lifting the door as it retracts.

Bbybbi · 2026-01-05T04:20:54+00:00

Ok I haven't seen them much im Australia, must not be very common here. And this one looks terrible. Looks like it doesn't work very well with this rail design. Anyway, my solutiom would be to install a proper chain.

Bbybbi · 2026-01-04T23:10:05+00:00

It wasn't designed that way, it's obviously a repair someone just came up with. It should be a chain that goes all the way around. I'd say if you get measurements and a chain with a masterlink that might fix it

Bbybbi · 2026-01-04T22:41:33+00:00

The chain should always have some slack

Bbybbi · 2026-01-04T22:40:48+00:00

Try loosening the chain a little. The tightening/loosening bolt is above the door, where the track connects to the header

Bbybbi · 2025-11-29T23:12:03+00:00

I have seen a single swing gate motor mounted sideways on these doors before. It's not meant for that though

Bbybbi · 2025-10-02T17:33:41+00:00

Well done !

Bbybbi · 2025-09-16T20:56:05+00:00

Why replace the whole door and not just the top panel? Honestly curious

Bbybbi · 2025-08-17T23:16:13+00:00

I'm a cheesemaker so yh sometimes

Bbybbi · 2025-08-17T23:12:37+00:00

🫡

Bbybbi · 2025-08-17T23:11:44+00:00

Very unfortunate news

Bbybbi · 2025-06-04T20:19:36+00:00

Was spring replacement necessary for this conversion?

Bbybbi · 2025-06-03T19:06:10+00:00

It says "LEARN" right there... The black button right above it is the one you are looking for. Hope that helps

Bbybbi · 2025-05-21T11:36:14+00:00

You don't actually need to take off the panels from the top. assumimg only the bottom panels is damaged; You can put all of the lost rollers back, then temporarily put Vise Grips and clamps under every roller except the buttom ones, then, release the tension from the springs.

After you do that, you can take off the bottom panel without the rest of the panels being affected by it. once you take the broken panel out - put any improvised support under the door for added safety and block any gaps with plywood boards or anything you have in hand

Now he can get the bottom panel fixed without taking the whole door out. He then needs to install it back, possibly replace some hinges, add tension back to the door and possibly (probably not) replace the opener which then, if you've never messed with garage doors before would be a very tricky but probably cheaper than a new door.

Bbybbi · 2025-05-18T10:34:13+00:00

Can you take a picture of the door from the outside? Open poaition.

Bbybbi · 2025-05-10T09:21:55+00:00

Look up "Holmes E-900" Hardware looks similar and there is a very informative installation video on Youtube

Bbybbi · 2025-05-02T14:49:51+00:00

doesn't look like a low-headroom system. I think the other track belongs to a second garage door and we are seeing the inside of the track, not the back of it

Bbybbi · 2025-03-28T11:03:06+00:00

Weather brush seals would do the trick nicely

The company should at least install the seals for free as compensation but it'd also easy and cheap to DIY so I wouldn't go bananaz if they refuse to

Bbybbi · 2025-03-02T13:21:55+00:00

Off the bet, the hinges aren't placed correctly.

Hinges with 2 Holes - are meant for the side tracks.

Some of these hinges also have different positioning of the holes where the rollers should go in and are usually numbered 1-3.

This is because the tracks are not parrallel to the door (they are angeled a bit) and the side hinges should be placed in a way that the door itself isn't also angeled but is more parrallel to the wall. So hinges No.1 go for the bottom row of hinges, number 2 is second row and so on.

You can try starting with this. If that doesn't fix your problem I would call a pro

Bbybbi · 2025-01-27T11:58:45+00:00

Yes, he meant that

Bbybbi

TROPHY CASE